Barbell Pin Good Morning

What Is the Barbell Pin Good Morning?
Barbell Pin Good Morning is a compound exercise that primarily targets the hamstrings and also engages the glutes, spinal erectors and adductors. It is an intermediate-level movement done inside a power rack, where each rep starts with the bar resting on the safety pins and the lifter already bent forward at the hips, so the lift begins from a dead stop at the bottom instead of after a lowering phase.
That bottom start is the point of the variation. In a standard Barbell Good Morning the lowering phase stretches the hamstrings and lets them rebound into the lift, while here the hamstrings, glutes and back have to produce force from a standstill in the hardest position of the rep. Powerlifting coaches use it as a squat and deadlift accessory for exactly that reason, and it pairs naturally with the Barbell Anderson Squat, the bottom-start version of the squat.
The pins also set the depth for every rep and give the bar somewhere to go if a rep stalls, which makes heavier good mornings more manageable to coach. Pin height changes the exercise: lower pins mean a deeper hinge, a longer hamstring stretch and more demand on the lower back, while higher pins shorten the range and allow more load. Because every rep starts without momentum, most lifters handle noticeably less weight than on a regular good morning.
It suits lifters who already own a solid hip hinge and can hold a flat lower back under a bar. Build up through the Bodyweight Good Morning, the Barbell Romanian Deadlift and the standard barbell good morning first, then add the pins once that hinge position stays solid at moderate loads. It usually sits after the main lifts of a session as a lower-rep strength accessory.
Muscles Worked
- Biceps Femoris
- Primary
- Semimembranosus
- Primary
- Semitendinosus
- Primary
- Erector Spinae
- High
- Gluteus Maximus
- High
- Adductor Magnus
- Medium
Instructions
- Set the safety pins of a power rack at the height the bar sits when you hinge forward with a flat back, usually around your hip height when standing. Test it with an empty bar.
- Load the bar resting on the pins, step under it and hinge at the hips with a slight knee bend.
- Place the bar across your upper traps, below the neck, and grip it just outside your shoulders.
- Set your feet about hip width apart under the bar with your weight over midfoot and knees softly bent.
- Pull your elbows down and squeeze your shoulder blades together to make a tight shelf for the bar.
- Take a deep breath, brace your trunk and flatten your lower back before the bar leaves the pins.
- Drive your hips forward and lift your torso until you stand tall, keeping your back flat and letting the knees straighten only as you finish.
- Exhale at the top, re-brace, then push your hips back to hinge forward and lower the bar under control.
- Set the bar down on the pins without dropping it and let it come to a full stop.
- Reset your brace and start the next rep from a standstill, then step out from under the bar after the last rep.
Common Mistakes
Setting the pins too low
If the bar can only reach the pins with a rounded lower back, every rep starts in a weak, flexed position, so raise the pins until the bottom feels solid.
Lifting before bracing
Breaking the bar off the pins before taking a breath and flattening the lower back lets the spine round under the heaviest part of the rep.
Squatting the bar up
Letting the knees bend and the hips drop as the weight climbs turns the lift into a squat and takes work away from the hamstrings.
Bouncing off the pins
Touching the pins and rebounding without a full stop removes the dead start the variation is meant to train.
Dropping the bar onto the pins
Crashing the bar down instead of lowering it under control jars the back and wastes the controlled lowering half of the rep.
Bar too high on the neck
Resting the bar on the neck instead of across the upper traps makes it painful and lets it roll as the torso tips forward.
Injuries
Barbell Pin Good Morning is a medium risk exercise when performed with proper technique. The bar sits on the upper back at the end of a long lever, so the lower back takes high loads, and starting each rep from a dead stop means the spine has to be braced and flat before the bar leaves the pins rather than settling into position on the way down. The hamstrings are also loaded in a stretched position at the start of every rep, and a bar set too high on the neck or held with cranked wrists can irritate the upper back, wrists and shoulders.
Set the pins at a height you can reach with a flat lower back, check it with an empty bar, and re-brace on every rep before you lift. Keep most sets a rep or two short of failure, since grinding reps are where the back tends to round, and set the bar down under control if a rep stalls instead of fighting it. Add load gradually, and lower the pins only in small steps once the current height feels solid.
If the bottom position is too demanding, regress to a lighter Barbell Good Morning, the Band Good Morning, the Barbell Romanian Deadlift or the Hyperextension. Progress by adding load, lowering the pins slightly or lengthening the pause on the pins.
Stop the set if you feel sharp or shooting pain in the lower back, pain, numbness or tingling running down a leg, or a sudden pull in the back of the thigh, and get it assessed before loading the movement again.
- Primary Focus
- Hamstrings
- Equipment
- Barbell
- Modality
- Strength
- Difficulty
- Intermediate
Alternative Exercises
Other Names for the Barbell Pin Good Morning
The Barbell Pin Good Morning is also known as:
- Concentric Good Morning
Frequently Asked Questions
- Q: Does a pin good morning start from the pins or from standing?
This version starts every rep with the bar resting on the pins in the bent-over position, so you lift first and lower second. Some coaches start standing and lower to a pause on the pins instead, which is closer to a paused Barbell Good Morning; both use the pins to take the bounce out of the bottom.
- Q: How high should I set the pins?
Set them so the bar rests on them at the deepest hinge you can hold with a flat lower back, usually with the torso just above parallel to the floor and the pins around hip height when you stand. Check the height with an empty bar, and lower the pins only in small steps.
- Q: How heavy should pin good mornings be?
Start well below your regular good morning, since there is no rebound to help, and use sets of about 3 to 6 reps stopped a rep or two short of failure. On the standard barbell good morning, a study of trained men found knee bend at the bottom rose from about 17 to 25 degrees as the load went from 50 to 90% of their max, so watch that heavier sets do not drift into a squat.
- Q: How is it different from a rack pull?
A Barbell Rack Pull holds the bar in the hands close to the legs and trains the top of the deadlift, while the pin good morning sets the bar across the upper back at the end of a long lever. That lever makes the good morning far lighter and puts more of the work on the hamstrings and lower back.
- Q: Why is it harder than a regular good morning?
In a regular good morning the lowering phase stretches the hamstrings and lets them rebound into the lift. Starting from a dead stop on the pins takes that rebound away, so the muscles have to produce all the force from a standstill in the bottom position.




