Machine Standing Hip Adduction

What Is the Machine Standing Hip Adduction?
Machine Standing Hip Adduction is an isolation exercise that primarily targets the hips and groin, especially the adductor longus and adductor magnus of the inner thigh, and also engages the hip stabilizers of the standing leg. It is a beginner-level movement performed on a standing multi-hip machine: you stand on the platform, hold the handles and pull a roller pad in toward the midline of your body with the inside of one leg while the other leg supports your weight.
The adductors draw the leg toward the body, and they work hard in sprinting, cutting, kicking and skating, which is why groin strains are so common in soccer and ice hockey. A 2025 review of 13 studies in healthy athletes found that players who went on to develop groin pain had weaker hip adductors at the start, while abductor strength and the ratio between the two showed no link. This machine loads the adductors directly with a selectable weight stack, so it is easy to progress in small steps and to train each side on its own. It usually sits after the main lower-body lifts as accessory work, or in a hip block alongside single-leg and lateral exercises.
Because you stand with the hip straight, the adductors work in the same hip position they use when you stand, walk and push off to the side. The seated Machine Hip Adduction bends the hips to about 90 degrees and squeezes both legs together, while Cable Hip Adduction follows a similar standing path with an ankle cuff instead of a lever pad. The standing leg is never just resting: its glutes and outer hip keep the pelvis level while the other leg moves, so both sides of the hip get some work.
It suits beginners, people returning to training, and athletes in cutting, kicking and skating sports who want targeted inner-thigh strength that squats and lunges only partly provide. If balance or the lightest plate is a problem, start with Side-Lying Hip Adduction or an Exercise Ball Lying Isometric Hip Adduction, then move to the machine. Mind-muscle connection matters here, because a twist of the pelvis or a lean of the torso can easily stand in for the hip movement, so aim to feel the inner thigh drawing the pad in on every rep.
Muscles Worked
- Adductor Longus
- Primary
- Adductor Magnus
- Primary
- Gluteus Medius
- Medium
- Peroneus Longus
- Minimal
- Soleus
- Minimal
Instructions
- Set the platform height so the machine's pivot lines up with the hip of your working leg, and set the roller pad so it rests against the inside of that leg around the knee.
- Step onto the platform, stand tall facing the handles and hold them with both hands.
- Place the inside of the working leg against the pad and shift your weight onto the standing leg, keeping that leg straight and the foot flat.
- Let the pad guide the working leg out to the side until you feel a light stretch in the inner thigh, keeping the leg long and the toes pointing forward.
- Brace your midsection, keep your chest up and your hips level and facing forward.
- Pull the pad in by drawing the working leg toward the standing leg, leading with the inner thigh rather than flicking the foot.
- Continue until the working foot reaches or crosses just in front of the standing foot, without twisting your pelvis or leaning your torso.
- Pause briefly and feel the inner thigh working.
- Let the pad carry the leg back out slowly, stopping at the same light stretch rather than letting the weight pull you wider.
- Finish your reps, then reset the pad for the other leg and repeat.
Common Mistakes
Leaning or twisting the torso
Tilting or rotating the upper body to help the leg across lets the trunk do part of the work and puts strain on the lower back.
Swinging the leg in
Pulling the pad in with momentum and letting it fly back out skips the controlled return and jerks the groin at its most stretched point.
Starting too wide
Letting the weight pull the working leg into a deep stretch under load strains the groin attachment without adding useful work.
Misaligning the pivot
Standing with the hip above or below the machine's pivot makes the pad roll along the leg and turns a smooth arc into an awkward push.
Hanging on the handles
Gripping hard and pulling with the arms to stay steady takes the balance work away from the standing leg and lets the torso shift.
Injuries
Machine Standing Hip Adduction is a low risk exercise when performed with proper technique. The loads are modest, the machine guides the leg along a fixed arc, and both hands hold the handles for balance, so there is little that can go badly wrong.
The groin, where the adductor longus attaches to the pubic bone, is the main strain point. It is most at risk when a heavy weight pulls the leg out into a deep stretch, or when a rep starts with a jerk from that stretched position, so set the outer range to a comfortable stretch and control the return every time. The lower back takes the strain when you lean or twist the torso to move more weight than the adductors can handle. A pad set low on the shin turns part of the pull into a sideways force on the inside of the knee, so if you feel it there, move the pad up to just above the joint. If you have pain on the outside of the hip, stop the working leg beside the standing leg instead of crossing it in front.
To make it easier, use Side-Lying Hip Adduction, an Exercise Ball Lying Isometric Hip Adduction or the seated Machine Hip Adduction. To make it harder, add weight in small steps, slow the return, pause at the end of each rep, or move on to the Copenhagen Plank (Bent Knee) and then the full Copenhagen Plank.
Stop if you feel sharp pain in the groin or over the pubic bone during a rep, or groin pain that lingers into the next day or flares when you sprint, kick or change direction, and have it checked before you load the movement again. After a recent groin strain, get clearance before returning to loaded adduction.
- Primary Focus
- Hips & groin
- Equipment
- Machine
- Modality
- Strength
- Difficulty
- Beginner
Alternative Exercises
Frequently Asked Questions
- Q: How is this different from the seated hip adduction machine?
Standing keeps the hip straight and trains one leg at a time while the other leg stabilizes, whereas the seated Machine Hip Adduction bends the hips to about 90 degrees and squeezes both legs together. In a study of 16 recreationally active adults on a hip dynamometer, peak eccentric adduction torque was lower with the hips bent to 90 degrees than at 0 or 45 degrees, while adductor longus activity stayed about the same. Both versions train the same muscles, so pick the one that fits your setup and goals.
- Q: Should my leg cross in front of the standing leg?
Bringing the working foot to just in front of the standing foot completes the range, and going much farther usually means the pelvis is twisting to help. If the outside of your hip is sore, stop the leg beside the standing leg instead.
- Q: How far out should I let the leg go?
Only to a light, comfortable stretch in the inner thigh that you can control on the way back in. A wider start under load stresses the groin attachment more than it trains the muscle.
- Q: Will this exercise slim my inner thighs?
No. It builds strength and muscle in the adductors, but training a muscle does not burn the fat over it, and fat loss comes from your overall diet and activity.
- Q: How many sets and reps should I do?
Two or three sets of 10 to 20 controlled reps per leg, with a slow return, suit most people. Add weight only when every rep stays free of leaning, twisting and swinging.
- Q: What can I do if my gym has no standing multi-hip machine?
Cable Hip Adduction follows the same standing path with an ankle cuff, and the seated Machine Hip Adduction trains the same muscles. At home, Side-Lying Hip Adduction and the Copenhagen Plank (Bent Knee) work well.




