Barbell Bent-Over Row (Wide Grip)

What Is the Barbell Bent-Over Row (Wide Grip)?
Barbell Bent-Over Row (Wide Grip) is a compound exercise that primarily targets the back and also engages the rear delts, the elbow flexors and the spinal erectors that hold the hinged position. It is an intermediate-level movement that takes an overhand grip about one and a half times shoulder width and rows the bar to the bottom of the rib cage with the elbows flared out to the sides.
The wide grip changes the path of the arms. In the standard Barbell Bent-Over Row the elbows travel back close to the ribs, and in the Barbell Bent-Over Row (Reverse Grip) they tuck in even further as the bar comes to the waist. With the hands set wide, the upper arms move out and back at an angle from the torso, so more of the pull comes from the muscles that draw the shoulder blades together and the arms back in that plane: the middle and upper trapezius, the rhomboids and the rear delts. The lats still do a large share of the work. The bar finishes higher on the torso, and the pull is a little shorter because the wider hands sit closer to the body at the top.
The variation is mainly used to build upper-back thickness, either in place of the standard row or as a second row on a pull or upper-body day. The wide overhand grip is harder to hold than a standard grip, so most lifters use a little less weight than on their usual row and work in moderate rep ranges where they can control the squeeze at the top.
It suits lifters who already row with a standard grip and want more upper-back and rear-delt work from a heavy compound pull. It is not the same lift as the Barbell Rear Delt Row, which raises the elbows to shoulder height with lighter loads to isolate the rear delts. Anyone who cannot yet hold a flat back in a loaded hinge can train the same wide-elbow pull with the chest supported, on the Chest-Supported T-Bar Row, the Barbell Seal Row or the Cable Seated Row (Wide Grip), while building the hinge separately.
Muscles Worked
- Latissimus Dorsi
- Primary
- Upper Trapezius
- Primary
- Deltoid
- High
- Erector Spinae
- High
- Lower Trapezius
- High
- Rhomboid Major
- High
- Teres Major
- High
- Biceps Brachii
- Medium
- Brachialis
- Medium
- Infraspinatus
- Medium
Instructions
- Stand with your feet about hip-width apart and the bar over the middle of your feet.
- Take an overhand grip about one and a half times shoulder width, well outside your legs.
- Lift the bar to standing, then soften your knees and hinge at the hips until your torso is bent well forward, about 45 degrees above the floor or lower.
- Let the bar hang at arm's length below your shoulders, brace your core and keep your back flat with your neck in line with your spine.
- Pull your shoulder blades back and row the bar up, driving your elbows out to the sides and up behind you.
- Bring the bar to the bottom of your rib cage, with your elbows bent about 90 degrees, your forearms close to vertical and your elbows rising above your back, a little below shoulder height.
- Squeeze your shoulder blades together for a moment without shrugging toward your ears.
- Lower the bar under control until your arms are straight, keeping your torso at the same angle.
- Repeat for the set, then stand up with the bar before setting it down.
Common Mistakes
Rounding the lower back
Letting the spine curl as the set gets hard moves the load from the hips and erectors onto the lumbar discs.
Standing up into the rep
Raising the torso a little more each rep shortens the pull and turns the row into a shrug.
Gripping too wide
Hands set so far out that the bar barely moves shorten the range and push the shoulders into a pinched position.
Shrugging the bar up
Lifting the shoulders toward the ears hands the work to the upper traps instead of drawing the shoulder blades back.
Jerking with the hips
Swinging the bar up with a hip thrust loads the lower back at speed and takes tension off the upper back.
Cutting the range short
Stopping before the bar reaches the ribs or never letting the arms straighten at the bottom skips both the squeeze and the stretch.
Injuries
Barbell Bent-Over Row (Wide Grip) is a medium risk exercise when performed with proper technique. The lower back is the main strain point, because the spinal erectors hold the bent-over torso against the full load for the whole set. A study of seven healthy men comparing three rowing exercises found the standing bent-over row placed the largest load on the lumbar spine, while the inverted row placed the lowest. Keep the back flat, brace before every rep and choose a weight you can row without the torso rising or rounding.
The wide grip adds a shoulder concern. With the hands far apart and the elbows flared, the upper arms sit raised out to the sides and turned inward, and a grip set wider than the shoulders tolerate, or a bar shrugged up with the shoulders rolling forward, can pinch the front or top of the joint. Grip only as wide as you can row without discomfort, keep the elbows a little below shoulder height and set the shoulder blades back and down before each pull. The wide overhand grip also loads the forearms and wrists, so keep the wrists straight rather than curled.
If the lower back is the limit, regress to a chest-supported row such as the Barbell Seal Row or the Chest-Supported T-Bar Row, or to the Barbell Inverted Row. If the shoulders are the limit, bring the grip in toward the standard Barbell Bent-Over Row. Progress by adding load in small steps or by pausing for a moment with the bar at the ribs. Stop the set for sharp lower-back pain, for pain, numbness or tingling running down a leg, or for a pinching pain in the shoulder that does not ease when the grip is narrowed.
Frequently Asked Questions
- Q: How wide should my grip be?
About one and a half times shoulder width, wide enough that the forearms stay close to vertical when the bar touches the bottom of the rib cage. Bring the hands in if the shoulders pinch or the bar can no longer reach the ribs.
- Q: Does a wide grip take the lats out of the row?
No. A 2026 review of latissimus dorsi EMG research reports that the one bent-over row study comparing grips, in 20 active young men rowing 60% of their one-rep max, recorded more lat activity with a grip 1.5 times shoulder width than with a shoulder-width grip. It is a single small study, so treat the wide grip as a way to share the work between the lats and the upper back rather than as a lat-focused row.
- Q: How is it different from the barbell rear delt row?
The Barbell Rear Delt Row drives the elbows straight out in line with the shoulders and uses lighter weight to isolate the rear delts. The wide-grip row keeps the elbows a little lower, rows to the bottom of the rib cage and handles heavier loads for the whole upper back.
- Q: Should I use straps?
The wide overhand grip is harder to hold than a standard grip, so straps are reasonable on heavy sets when the hands give out before the back does. Do lighter sets without them so grip strength keeps up.
- Q: Should I use it instead of the standard bent-over row?
It works well as a swap or as a second row in the same session, since the two grips share the work between the lats and upper back differently. Many lifters keep the standard Barbell Bent-Over Row as their heavy row and use the wide grip for moderate-rep upper-back work.




