Cable Bent-Over Row

What Is the Cable Bent-Over Row?
Cable Bent-Over Row is a compound exercise that primarily targets the back and also engages the rear shoulders, biceps, forearms and lower back. It is an intermediate-level movement in which you stand facing a low pulley, hinge forward at the hips, and row a straight bar from arm's length into your lower stomach with an overhand grip.
The exercise builds the lats and the muscles between the shoulder blades through a horizontal pull, the same job as the Barbell Bent-Over Row, but with a weight stack in place of plates. Changing the load takes a moment with the pin, nothing has to be pulled from the floor to start the set, and the stack can go light enough to teach the pattern. That makes it a practical main row on a lighter day, a back accessory after pull-ups or a heavier row, or a good fit for higher-rep sets and drop sets.
Because the cable runs up at an angle from the floor pulley, it pulls the bar toward the machine as well as down. You have to sit your hips back and keep your weight over your heels to stop it dragging you forward, and the same angle keeps your back loaded in the stretched position with your arms straight. The overhand, shoulder-width grip on a straight bar spreads the work across the lats and upper back, while switching to an underhand grip keeps the elbows tighter and brings in more biceps. Unlike the Cable Seated Row, no seat or foot platform holds you in place, so your lower back and hamstrings hold the hinge for the whole set. Unlike the Cable Single-Arm Bent-Over Row, both arms pull together, so there is no twist to resist and you can usually handle more weight, but a stronger side can quietly do more of the work.
This variation suits lifters who want a bent-over row that is quick to load and adjust, and trainers who want a controllable way to teach rowing from a hinge before moving a client to the barbell. If holding the hinge is the limiting factor, learn the position first with the Dumbbell Romanian Deadlift and build rowing strength with a supported option such as the Dumbbell Incline Row or the seated cable row.
Muscles Worked
- Latissimus Dorsi
- Primary
- Deltoid
- High
- Rhomboid Major
- High
- Teres Major
- High
- Upper Trapezius
- High
- Biceps Brachii
- Medium
- Brachialis
- Medium
- Brachioradialis
- Medium
- Erector Spinae
- Medium
Instructions
- Attach a straight bar to a pulley set at its lowest position and select a light weight.
- Grab the bar with an overhand grip, hands about shoulder-width apart, and step back from the machine with your feet hip-width apart.
- Push your hips back and bend your knees slightly until your torso is about 45 degrees to the floor, with your back flat and your neck in line with your spine.
- Let your arms hang straight toward the pulley with the weight lifted off the stack, your weight over your heels and your core braced.
- Pull the bar toward your lower stomach by driving your elbows back past your torso.
- Squeeze your shoulder blades together as the bar reaches your stomach, keeping your torso angle unchanged.
- Lower the bar under control until your arms are straight again, without letting the weight touch the stack.
- Repeat for the desired reps, then step toward the machine to set the weight down before standing up.
Common Mistakes
Rounding the lower back
Letting your spine curve as the bar reaches toward the pulley moves the load from your hips and back muscles onto your lower back.
Getting pulled toward the stack
Shifting onto your toes lets the angled cable drag you forward, so sit your hips back and keep your weight over your heels.
Standing up as you row
Lifting your chest with each rep uses hip momentum to move the bar and takes work away from your back.
Shrugging the bar
Pulling your shoulders up toward your ears turns the row into a shrug and takes tension off the lats and mid back.
Cutting the range short
Stopping before your arms are straight or before the bar reaches your stomach skips both the stretch and the full squeeze.
Letting the stack crash
Dropping the weight between reps loses tension and jolts your shoulders and lower back.
Injuries
Cable Bent-Over Row is a medium risk exercise when performed with proper technique. The main strain point is the lower back, which holds the hip hinge for the whole set while the cable pulls the bar forward and down. Rounding the lower back, or letting the stack drag your chest toward the machine, shifts that load from your hips and back muscles onto the spine. The shoulders can also be irritated by shrugging the bar toward your ears or by yanking the weight from a fully stretched start.
Warm up your hips and hamstrings, start with a light stack, and set a torso angle you can hold with a flat back. Around 45 degrees works for most people, and bending lower is not required. Brace your core before each rep, keep your weight over your heels, and lower the bar under control rather than letting the plates crash.
If your lower back tires before your upper back does, switch to a supported row such as the Cable Seated Row, Dumbbell Incline Row or Chest-Supported T-Bar Row. To progress, add load gradually, slow the lowering phase, pause with the bar at your stomach, or move to the Barbell Bent-Over Row.
Stop the set if you feel sharp or radiating pain in your lower back or down a leg, pinching at the front of the shoulder, or if you can no longer keep your back flat. Pain that lingers after training should be checked by a qualified professional before you load the movement again.
Frequently Asked Questions
- Q: How is the Cable Bent-Over Row different from the Cable Seated Row?
In the Cable Seated Row, the seat and foot platform hold your body in place. Here you stand and hold a hip hinge yourself, so your lower back and hamstrings work throughout the set and the cable runs up at an angle from the floor pulley.
- Q: Should I row with both arms or one arm at a time?
Rowing a bar with both arms keeps your torso square and usually lets you move more weight. The Cable Single-Arm Bent-Over Row trains each side on its own and makes your core resist twisting, which suits evening out a stronger and weaker side.
- Q: How far should I stand from the machine?
Stand far enough back that the weight lifts off the stack with your arms straight and the bar clears your knees. If you have to fight to stay balanced as the cable pulls you forward, step a little closer or lighten the load.
- Q: Can I use an underhand grip on the bar?
Yes. An underhand grip keeps your elbows closer to your sides and brings in more biceps, much like the Barbell Bent-Over Row (Reverse Grip), while the overhand grip shown here spreads more of the work across the upper back.
- Q: Can the Cable Bent-Over Row replace the Barbell Bent-Over Row?
For building the back, yes, since both train the same bent-over pulling pattern. The Barbell Bent-Over Row is easier to load very heavy, while the cable version makes small weight changes simple and keeps your back loaded with your arms straight at the bottom.




