Barbell Floor Press (Reverse Grip)

Barbell Floor Press (Reverse Grip)

What Is the Barbell Floor Press (Reverse Grip)?

Barbell Floor Press (Reverse Grip) is a compound exercise that primarily targets the chest and also engages the front shoulders, triceps and biceps. It is an intermediate-level movement in which you lie on the floor with your legs straight and press a barbell held with an underhand grip, palms facing toward your head, stopping each rep when your upper arms reach the floor.

The exercise combines two familiar changes to the bench press. Pressing from the floor, as in the Barbell Floor Press, cuts off the bottom of the range, removes leg drive when the legs stay straight and makes every rep start from a dead stop, so the top half of the press and the lockout, where the triceps work hardest, get most of the work. The underhand grip, as in the Barbell Bench Press (Reverse Grip), keeps the elbows tucked close to the sides and moves the bar's lowest point down toward the lower chest.

The grip also changes which muscles share the load. On the flat bench press, an isometric study of 12 healthy men found that a supinated grip increased activity in the biceps and in the clavicular (upper) head of the chest, while grip width changed muscle activity only modestly. The chest still does most of the work, with the front shoulders and triceps close behind.

It fits as an accessory after the main pressing work of a session, for lifters who want reverse grip pressing with a built-in depth limit, who press at home without a bench, or who find the underhand grip and shorter range more comfortable on their shoulders. Because grip security and wrist position limit the load more than the pressing muscles do, it is trained with moderate weights and controlled reps rather than heavy singles.

It suits lifters who are already comfortable with the overhand Barbell Floor Press and have a firm, fully wrapped grip. Anyone new to floor pressing can build up with the Dumbbell Floor Press first, and lifters whose wrists do not tolerate the underhand barbell grip can use the Dumbbell Hammer Bench Press instead.

Muscles Worked

MuscleActivation

Instructions

  1. Set the bar in a power rack on hooks you can reach with straight arms while lying on the floor, and set the safety arms just below the bottom position.
  2. Lie on your back under the bar with it over your lower chest, legs straight on the floor and head resting on the floor.
  3. Take an underhand grip about shoulder width, palms facing toward your head, with the thumbs wrapped around the bar and the bar in the heels of your hands.
  4. Keep your wrists straight over your forearms, pull your shoulder blades back and down, and brace your core.
  5. Press the bar off the hooks and hold it at arm's length over your shoulders.
  6. Lower the bar under control toward your lower chest, keeping your elbows tucked close to your sides.
  7. Stop when your upper arms rest on the floor and pause briefly without relaxing.
  8. Press the bar back up until your arms are straight, letting it travel slightly back to finish over your shoulders.
  9. Repeat for the planned reps, then return the bar to the hooks while keeping your grip tight.

Common Mistakes

  • Loose or thumbless grip

    An underhand grip without the thumbs wrapped lets the bar roll toward the fingers and slip, so wrap the thumbs fully and squeeze the bar before every set.

  • Wrists folding back

    Letting the bar sit in the fingers bends the wrists back and strains them, so set the bar in the heel of the hand with the wrists straight over the forearms.

  • Flaring the elbows

    Pushing the elbows out away from the body fights the underhand grip and twists the wrists, so keep them tucked close to the sides as the bar comes down.

  • Bouncing off the floor

    Dropping the upper arms onto the floor and rebounding jars the elbows and takes the dead-stop strength work out of the rep, so lower slowly and pause.

  • Bar drifting toward the face

    Pressing the bar back over the face or neck puts it where a slip does the most harm, so lower it to the lower chest and press it up to a point over the shoulders.

  • No safeties or spotter

    Pressing heavy with an underhand grip and nothing to catch the bar leaves no way out of a missed or slipped rep, so set safety arms just below the bottom position or use a spotter.

Injuries

Barbell Floor Press (Reverse Grip) is a medium risk exercise when performed with proper technique. The floor stops the upper arms before the shoulders reach the deep stretch of a bench press, which keeps shoulder stress lower than in the Barbell Bench Press (Reverse Grip). The underhand grip is less secure than an overhand one, though, and the bar travels over the chest and neck, so a slipping bar is the main danger.

The usual strain points are the wrists and forearms, which have to hold the bar in the heel of the hand without folding back, and the elbows, which take a hard push at lockout and a jolt if the upper arms bounce off the floor. Wrap the thumbs fully around the bar, use chalk or a well-knurled bar, keep the wrists straight over the forearms and lower the bar slowly to a soft stop on the floor. Set safety arms in a rack just below the bottom position, or use a spotter, for anything close to a heavy set.

If the underhand grip strains the wrists, go back to the overhand Barbell Floor Press or press a pair of dumbbells with a neutral grip in the Dumbbell Floor Press. Once the grip feels secure over many sets, the reverse grip bench press adds the full range of motion. Stop the set if the bar starts to roll in your hands, if you feel sharp pain in the wrist, elbow or front of the shoulder, or if you feel a pulling or tearing sensation in the chest or armpit.

Frequently Asked Questions

Q: Why use a reverse grip on the floor press?

The underhand grip keeps the elbows tucked close to the body and shifts a little more of the work to the upper chest and biceps. Some lifters also find it more comfortable on the shoulders, especially with the floor limiting how deep the arms can go.

Q: Should my legs be straight or bent?

Both are used. Straight legs, as shown here, remove leg drive so the upper body does all the work, while bent knees with the feet flat can feel more stable for the lower back. Pick one setup and keep it the same so your progress is comparable.

Q: How much weight should I use compared with a regular floor press?

Start noticeably lighter than your overhand floor press. The limit is usually how securely you can hold the bar with an underhand grip and keep your wrists straight, so add weight only once the grip feels solid on every rep.

Q: Is it safer than the reverse grip bench press?

Somewhat. The floor stops the arms before the shoulders reach a deep stretch, but the bar can still slip from an underhand grip, so it needs the same wrapped grip, safety arms or spotter as the Barbell Bench Press (Reverse Grip).

Q: Should I pause with my arms on the floor?

Yes. A brief pause with the upper arms resting on the floor, while the muscles stay tight, removes any bounce and makes each rep start from a dead stop.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.