Barbell Pin Squat

What Is the Barbell Pin Squat?
Barbell Pin Squat is a compound exercise that primarily targets the quadriceps and also engages the glutes, adductors and lower back. It is an advanced-level movement in which you lower a back-squatted barbell onto safety pins set inside a power rack, let it come to a complete stop, and then stand back up. Resting the bar on the pins takes away the bounce out of the bottom, so every rep has to be driven up from a standstill.
The pin squat is mainly a strength and powerlifting tool. It is used as a secondary squat variation, after the main squat or on a lighter squat day, to build strength out of the bottom position, to work a sticking point at a chosen height, and to make depth consistent, since the pins tell you exactly when you have reached it. The name is also used for a version that starts with the bar resting on the pins and has no lowering phase at all; that bottom-up version is covered on its own page as the Barbell Anderson Squat.
Pin height decides how much range of motion you train. Pins set so the bar touches at about parallel work much the same range as a regular Barbell Squat, while raising them shortens the lift toward a Barbell Quarter Squat. Depth matters for results: in a 10-week study of men doing full squats versus half squats, the full squat group gained more full-squat strength and more glute and adductor muscle, while quadriceps growth was similar in both groups.
The pin squat sits between two close relatives. Unlike a Barbell Box Squat, the pins stop only the bar, so your hips and legs stay loaded and there is nothing to sit back and relax onto. Compared with a Paused Barbell Squat, where you hold the bottom position under full load, letting the bar settle on the pins releases more of that built-up tension, so the drive up has to be produced more abruptly.
This variation suits lifters who already squat with consistent depth and a solid brace. If the regular back squat is still being learned, build up with the Barbell Squat, the Barbell Box Squat or the Smith Machine Box Squat first, and expect to start lighter than your regular squat when you add pin squats, because the bottom of the lift is harder without the rebound.
Muscles Worked
- Vastus Lateralis
- Primary
- Vastus Medialis
- Primary
- Adductor Magnus
- High
- Gluteus Maximus
- High
- Rectus Femoris
- High
- Erector Spinae
- Medium
- Soleus
- Low
Instructions
- Set the safety pins in a power rack so the bar will touch them when your thighs are about parallel to the floor, and set the hooks at about upper chest height.
- Step under the bar and rest it across your upper traps, gripping it with your hands just outside your shoulders.
- Stand up to unrack the bar, take a step or two back so you are standing over the pins, and set your feet about shoulder-width apart with your toes turned slightly out.
- Take a deep breath and brace your trunk.
- Bend your hips and knees together to lower the bar under control, keeping your chest up and your knees tracking over your toes.
- Keep lowering until the bar settles softly onto the pins, without dropping or bouncing it.
- Let the bar come to a complete stop for a moment while you keep your brace and upper back tight.
- Drive up through your whole foot, lifting the bar off the pins with your hips and shoulders rising together until you are standing tall.
- Breathe out at the top, then breathe in and brace again before the next rep. After the last rep, walk the bar forward into the hooks.
Common Mistakes
Setting the pins at the wrong height
Pins set too low force you to fold forward to reach them, while pins set too high cut short the depth you meant to train.
Dropping the bar onto the pins
Letting the bar crash down creates a bounce that defeats the dead stop and jars the spine and shoulders.
Relaxing on the pins
Letting the brace and upper back go loose while the bar rests means the drive starts from a slack, rounded position.
Reaching for the pins with the chest
Leaning forward to feel for the pins instead of squatting to your normal depth shifts the load onto the lower back.
Hips shooting up first
Driving the hips up faster than the bar off the pins turns the lift into a good morning and loads the lower back.
Injuries
Barbell Pin Squat is a medium risk exercise when performed with proper technique. The bar is heavy and loaded across the upper back, and the hardest moment of the lift comes right where the bar sits still on the pins, so the lower back, knees and hips take most of the strain. The pins do add a safety stop, since a missed rep can be lowered onto them instead of ending in a fall.
Most problems come from the setup. Pins set too low make you fold forward or lose your back position to reach them, which loads the lower back, and pins set too high cut the depth you meant to train. Test the height with an empty bar before loading it. Lower the bar onto the pins under control rather than dropping it, because a hard landing on metal pins jars the spine and shoulders and makes the bar bounce. Keep your brace and upper back tight while the bar rests, so the first inch of the drive does not start from a slack, rounded position.
If the pin squat feels unstable or stresses your back, regress to a Barbell Box Squat, a Smith Machine Box Squat or a Dumbbell Goblet Squat, or simply raise the pins a notch. Progress by lowering the pins toward full depth, holding the stop a little longer, or moving to the Barbell Anderson Squat, which starts from the pins with no lowering phase. Stop the set if you feel sharp pain in the knees, hips or lower back, a pinching sensation at the front of the hip at the bottom, or numbness or tingling down the legs.
Frequently Asked Questions
- Q: Do you start a pin squat from the pins or lower down to them?
Both versions go by the name pin squat. This page covers the version where you start standing and lower the bar to the pins, and the version that starts with the bar resting on the pins is the Barbell Anderson Squat.
- Q: How high should I set the pins?
Set them so the bar touches at the depth you want to train, which for full range is with your thighs about parallel to the floor or just below. Check the height with an empty bar, because you should reach the pins in your normal squat position without leaning forward to find them.
- Q: How long should the bar rest on the pins?
Long enough for the bar to come to a complete stop, usually a second or so, without bouncing it off the pins. Keep your brace and upper back tight the whole time rather than letting the pins take the weight while you relax.
- Q: What is the difference between a pin squat and a box squat?
In a Barbell Box Squat your body sits on the box, while in a pin squat only the bar rests on the pins and your legs and hips stay loaded. That makes the pin squat harder to cheat by relaxing at the bottom.
- Q: How should I program pin squats?
Most lifters use them as a secondary squat, after the main squat or on a lighter day, in sets of about 3 to 5 reps. Start lighter than your regular squat, since standing up from a dead stop is harder than rebounding out of the bottom.




