Barbell Reeves Deadlift

Barbell Reeves Deadlift

What Is the Barbell Reeves Deadlift?

Barbell Reeves Deadlift is a compound exercise that primarily targets the back, glutes, and hamstrings and also engages the quadriceps, forearms, and shoulders. It is an advanced-level movement because the lifter pulls the barbell by gripping the rims of the weight plates instead of the bar, which turns a standard deadlift into a very wide-grip pull with a demanding grip challenge.

The lift is named after Steve Reeves, the 1947 Mr. America and 1950 Mr. Universe winner who went on to play Hercules on film, and it is commonly credited as an upper-back exercise from his training. The weights attributed to Reeves himself are not reliably documented. Today it is also a contested lift in all-round weightlifting: the USAWA rules have the lifter grip one plate on each side and add weight with smaller-diameter plates, and the IAWA (UK) calls the same lift the Rim Lift.

With the hands far outside the shoulders and the arms angled out to the sides, the trapezius, upper back, and shoulders work hard just to hold the bar in place, while the glutes, hamstrings, and spinal erectors drive the hinge as in any deadlift. The wide reach means the lifter starts with the hips lower and the torso more bent than in a Barbell Deadlift, much like a Barbell Deadlift (Snatch Grip) taken further. Grip is almost always the limiting factor, so the loads are well below a conventional deadlift, and larger plates widen the reach and make the hold harder.

The Barbell Reeves Deadlift suits lifters who already deadlift with solid technique and want more upper-back and grip work, including strongman and grip enthusiasts. It usually sits after the main pulls of a session as an accessory. Lifters who cannot yet hold the plates should build up with the Barbell Deadlift (Snatch Grip) for the wide-grip hinge and the Weight Plate Pinch for the grip.

Muscles Worked

MuscleActivation
Deltoid
Medium

Instructions

  1. Load the barbell with one large iron plate per side, lipped side facing out, and secure them with collars.
  2. Stand with your feet about hip-width apart and toes turned slightly out, with the bar over the middle of your feet.
  3. Push your hips back and bend your knees until you can reach the plates, then grip the top of each plate's rim with your fingers on one face and your thumb on the other.
  4. Keep your arms straight and angled out toward the plates, set your back flat, and lift your chest so your hips sit above your knees and below your shoulders.
  5. Brace your core and drive through your feet, extending your hips and knees together so the plates leave the floor without your hips rising first.
  6. Keep your arms straight and your grip even on both plates as the bar rises in front of your legs.
  7. Finish standing tall with your hips and knees straight, shoulders back, and the bar hanging in front of your thighs, without leaning back.
  8. Lower under control by pushing your hips back first, then bending your knees once the bar passes them, keeping your back flat until the plates touch the floor.
  9. Reset your grip on both rims before the next rep.

Common Mistakes

  • Rounding the back to reach the plates

    The wide reach tempts lifters to round the spine to grab the rims, so lower the hips and set a flat back before the plates leave the floor.

  • Letting the hips shoot up first

    Raising the hips before the plates move turns the lift into a stiff-legged pull and loads the lower back, so drive the hips and chest up together.

  • Bending the elbows

    Pulling with bent arms strains the elbows and biceps, so keep the arms straight and let them act as hooks from start to finish.

  • Using plates that are hard to hold

    Thick bumper plates have no lip to grip and slip early, so use plain iron plates with the lipped side facing out.

  • Gripping one side more securely

    When one hand holds less of the rim, that side slips first and the bar tilts, so match the hand position on both plates before each rep.

  • Leaning back at lockout

    Overextending the lower back at the top adds strain without extra work for the hips, so finish standing tall with the hips and knees just straight.

Injuries

Barbell Reeves Deadlift is a medium risk exercise when performed with proper technique. The lower back is the main strain point, because the wide reach pulls the chest down toward the floor and makes it easy to round the spine before the plates leave the ground. The shoulders also work in an unusual position, holding the arms out to the sides under load, and the fingers and thumbs take a hard pinch on the plate rims.

Start light, with plates you can hold securely, and keep the back flat and the arms straight on every rep. Use plain iron plates with a lip to grip rather than thick bumper plates, put collars on the bar, and keep the feet clear of the plates in case the grip fails. If one hand starts to slip, set the bar down rather than finishing the rep with a tilted bar.

To regress, practice the wide-grip hinge with the Barbell Deadlift (Snatch Grip) and build the hold with the Weight Plate Pinch. To progress, add weight with smaller-diameter plates so there is still one plate per side to grip, or pause at the top of each rep. Stop if you feel sharp pain in the lower back, pain in the front or top of the shoulder, or pain at the base of the thumb, and do not train through numbness or tingling in the hands.

Other Names for the Barbell Reeves Deadlift

The Barbell Reeves Deadlift is also known as:

  • Rim Lift

Frequently Asked Questions

Q: Why is it called the Reeves deadlift?

It is named after Steve Reeves, the 1940s and 1950s bodybuilding champion and Hercules film star, who is credited with using it to build his upper back. The heavy weights often attributed to him in this lift are not reliably documented.

Q: How is it different from a snatch-grip deadlift?

Both use a wide grip, but the Reeves deadlift places the hands even wider, on the plates themselves, and replaces a normal bar grip with a pinch on the rims. That makes grip the limiting factor and keeps the loads lower than a Barbell Deadlift (Snatch Grip).

Q: Can I use lifting straps or plates with handles?

You can for upper-back training, but it removes the plate grip that defines the lift, and lifters disagree on whether a strapped or handled pull still counts as a Reeves deadlift. Competition rules have the lifter grip the plates themselves.

Q: How do I add weight without making the grip impossible?

Keep one large plate per side as the gripping plate and load extra weight with smaller-diameter plates, as the all-round weightlifting rules do. A larger gripping plate widens the reach and makes the hold harder, so change the small plates and leave the gripping plate alone.

Q: What kind of plates work best?

Plain iron plates with a raised lip are the easiest to grip, especially with the lip facing out. Thick bumper plates are smooth and wide, which makes them very hard to pinch.

Q: How many sets and reps should I do?

As an accessory, 3 to 4 sets of 5 to 8 reps works well, ending each set when the grip starts to slip rather than when the back tires. Treat it as upper-back and grip work after your main pulls, not as a test of maximal strength.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.