Machine Kneeling Glute Kickback

What Is the Machine Kneeling Glute Kickback?
Machine Kneeling Glute Kickback is an isolation exercise that primarily targets the glutes and also engages the hamstrings and adductor magnus. It is a beginner-level movement performed on all fours on the floor, pressing the sole of one foot back and up against the roller pad of a selectorized lever machine.
The movement trains hip extension one leg at a time against a weight stack, so the load is easy to set and to raise in small steps. Working each side alone also makes it easy to spot a left-right difference in strength or control. It has no competition or testing role; it is a glute accessory, usually placed after the main lower-body lifts such as squats, deadlifts or the Barbell Hip Thrust and trained for moderate to higher reps.
The gluteus maximus drives the leg back from a bent hip to a fully extended one, with the hamstrings assisting. Because the foot pushes the pad rather than hanging free, the knee also opens partway as the leg travels back, which brings in a little quadriceps work that a Bent Leg Kickback does not have. The Cable Donkey Kickback and the Smith Machine Kneeling Glute Kickback train the same kneeling pattern with different resistance, while the Machine Glute Kickback is the standing version.
It suits beginners and anyone who wants direct glute work without a load on the spine. Range is limited by how well the lower back stays still, not by how high the foot can go, so the useful focus is feeling the glute finish the movement. If holding a still pelvis on all fours is hard, build it first with the Bent Leg Kickback and the Glute Bridge.
Muscles Worked
- Gluteus Maximus
- Primary
- Biceps Femoris
- High
- Adductor Magnus
- Medium
- Semimembranosus
- Medium
- Semitendinosus
- Medium
Instructions
- Select a light weight on the stack and set the lever arm so its roller pad sits behind you at about hip height when you kneel.
- Kneel on all fours on a mat facing away from the machine, with your hands flat under your shoulders, arms straight and the support knee under your hip.
- Place the sole of your working foot flat against the roller pad, with that knee bent about 90 degrees and the thigh under your hip.
- Brace your core, keep your back flat and your head in line with your spine, looking at the floor.
- Drive the foot back and up into the pad by extending your hip, letting the knee open partway as the leg travels back.
- Stop when the thigh is roughly in line with your torso and the knee is still bent, with the sole pressing up into the pad, without arching your lower back or turning the hip outward.
- Squeeze the glute for a moment at the top.
- Lower the pad under control until the knee is back under your hip, without letting the weight stack touch down.
- Complete all reps on one side, then switch legs.
Common Mistakes
Arching the lower back
Pushing the foot higher than the hip can extend lets the lumbar spine arch, which moves the work from the glute into the lower back.
Rotating the hips
Letting the working hip lift and turn outward at the top adds height through the pelvis instead of through hip extension.
Kicking with momentum
Swinging the pad back fast lets the weight stack carry the leg through the top instead of the glute driving it.
Dropping the weight on the way down
Letting the stack fall back skips the controlled lowering phase and often bangs the plates together between reps.
Sagging through the shoulders
Letting the chest sink between the arms or the head drop loosens the trunk and makes it harder to keep the spine neutral.
Loading too heavy
A weight you cannot move without arching or twisting turns the set into a lower back and momentum exercise.
Injuries
Machine Kneeling Glute Kickback is a low risk exercise when performed with proper technique. The load is light compared with compound hip lifts and nothing presses down on the spine, so problems mostly come from position rather than weight.
The lower back is the usual strain point. Chasing extra height arches the lumbar spine and lets the lower back finish the movement instead of the glute. Brace the trunk, keep the pelvis level and only raise the leg as far as the lower back can stay still. The support knee and the wrists also carry weight on the floor, so kneel on a mat and keep the hands directly under the shoulders.
If the movement is hard to control, regress to the Bent Leg Kickback or the Glute Bridge until the pelvis stays still. To progress beyond the machine, the Barbell Hip Thrust or the Machine Hip Thrust allow much heavier hip extension work.
Stop the set if you feel pinching or pain in the lower back, sharp pain in the hip or the front of the knee, or wrist pain that does not ease when you shift your weight.
Other Names for the Machine Kneeling Glute Kickback
The Machine Kneeling Glute Kickback is also known as:
- Machine Donkey Kickback
Frequently Asked Questions
- Q: How high should my leg go?
Stop when the thigh is roughly in line with your torso, or as high as you can go while your lower back stays still. Any height beyond that comes from arching the spine, not from the glute.
- Q: Is the kneeling kickback machine better than the hip thrust for glutes?
Neither replaces the other. The Barbell Hip Thrust lets you load both hips heavily, while the kickback works one side at a time with lighter weight, so most glute programs use the thrust as the main lift and the kickback as an accessory.
- Q: How many sets and reps should I do?
Most people do 2 to 4 sets of 10 to 15 reps per leg after their main lower-body lifts. Pick a weight that lets you pause briefly at the top of every rep without arching or twisting.
- Q: Why do I feel it more in my lower back or hamstrings than my glutes?
Lower back strain usually means the spine is arching at the top, so shorten the range and brace harder. Feeling the hamstrings is normal because they help extend the hip, but pausing and squeezing the glute at full hip extension keeps the glute doing most of the work.
- Q: What can I do if my gym has no kickback machine?
The Cable Donkey Kickback and the Band Kneeling Single-Leg Kickback train the same kneeling pattern, and the Bent Leg Kickback needs no equipment at all.




