Smith Machine Kneeling Glute Kickback

What Is the Smith Machine Kneeling Glute Kickback?
Smith Machine Kneeling Glute Kickback is an isolation exercise that primarily targets the glutes and also engages the hamstrings, the adductor magnus and the quadriceps. It is an intermediate-level movement in which you kneel on all fours on a flat bench inside a Smith machine and press the bar upward with the sole of one foot by extending the hip. Because the bar runs on fixed rails and takes plates, it can be loaded far beyond what a band or ankle weight allows, which makes it a practical way to add progressive overload to a kickback.
The exercise is a glute accessory rather than a main lift. It usually comes after the heavier hip and leg work of a session, such as squats, hip thrusts or Romanian deadlifts, and is trained one leg at a time for moderate to higher reps. Working each side alone also makes it easy to notice when one glute is weaker or tires sooner than the other.
The knee stays bent throughout, so the hamstrings, which also bend the knee, help less than in a straight-leg kickback and the hip extension falls mostly to the gluteus maximus. The bodyweight Bent Leg Kickback is the same pattern without load, the Cable Glute Kickback pulls along the line of the cable rather than straight down, and the Machine Glute Kickback moves the leg along a fixed arc with a simpler setup. The Smith machine version asks more of the lifter: balancing on a bench, keeping the foot centered under a loaded bar and setting the safety stops correctly.
It suits lifters who want more direct glute work than their compound lifts give them, and who are already comfortable holding a neutral spine on all fours. Anyone new to the pattern should first learn it with the Bent Leg Kickback and the Glute Bridge. The range of motion is short and the lower back can easily take over the last part of it, so feeling the glute finish each rep matters more here than in most lower-body exercises.
Muscles Worked
- Gluteus Maximus
- Primary
- Adductor Magnus
- Medium
- Biceps Femoris
- Medium
Instructions
- Place a flat bench inside the Smith machine so that, kneeling on it on all fours, your hips sit just in front of the bar.
- Set both safety stops at the same height, just below where the bar will rest with your working knee bent about 90 degrees, and load the plates evenly.
- Unlatch the bar and lower it onto the safety stops so it can slide freely.
- Kneel on the bench on all fours, hands gripping the front of the bench under your shoulders with straight arms and the supporting knee under your hip.
- Raise the working leg with the knee bent about 90 degrees and place the arch of that foot flat under the bar.
- Brace your trunk and keep your back flat and your head in line with your spine.
- Press the bar up with the sole of your foot by extending your hip until your thigh is in line with your torso, keeping the knee bent.
- Squeeze the glute at the top for a moment without arching your lower back or turning your hip open.
- Lower the bar under control until it is just above the stops, then start the next rep.
- After the last rep, set the bar down on the stops before moving your foot, then switch legs.
Common Mistakes
Arching the lower back
Driving the bar higher than the hip can extend makes the lumbar spine arch, which moves the load from the glute onto the lower back.
Rotating the hips open
Turning the working hip toward the ceiling lets the trunk twist and shortens the glute's share of the rep.
Pressing with the toes
Pushing the bar with the toes or the edge of the foot lets it tilt or roll, so keep the arch of the foot centered under the bar.
Straightening the knee to push
Kicking the knee straight turns the rep into a single-leg press and hands much of the work to the quadriceps.
Setting the safety stops wrong
Stops left too low, or at uneven heights, cannot catch the bar if your foot slips.
Dropping the bar onto the stops
Letting the bar fall and bounce off the stops between reps loses tension on the glute and jolts the foot and knee.
Injuries
Smith Machine Kneeling Glute Kickback is a medium risk exercise when performed with proper technique. The hip extension itself is gentle on the joints, but the setup places a loaded bar above your leg while you balance on a bench, and the bar rests only on the sole of your foot. If the foot slides or the bar tilts, the bar can drop toward your leg or come down unevenly.
The most common strain point is the lower back. Pushing the bar higher than the hip can extend makes the lumbar spine arch to finish the rep, and repeated under load this can irritate the lower back. Some people also feel pressure on the supporting knee from the bench, pinching at the front of the working hip at the bottom of the rep, or strain in the wrists from bracing on the bench edge.
Set both safety stops at the same height, just below the lowest point the bar reaches with your knee bent, so a slip ends on the stops rather than on your leg. Load the plates evenly, wear flat shoes with a firm sole that grips the bar, center the arch of the foot under it, and stop each rep where your hip finishes extending rather than where your back can push the bar. A folded mat under the supporting knee eases bench pressure. If the setup feels unstable, regress to the Bent Leg Kickback or the Band Kneeling Single-Leg Kickback; once the pattern is solid, add load gradually, pause at the top or slow the lowering phase, and use the Barbell Hip Thrust for heavier hip extension work.
Stop the set if you feel sharp pain in the lower back, a pinch in the front of the hip, knee pain on the bench, or numbness or tingling in the leg, and stop at once if the bar starts to roll toward your toes or heel.
- Primary Focus
- Glutes
- Equipment
- Smith machine and bench
- Modality
- Strength
- Difficulty
- Intermediate
Alternative Exercises
Other Names for the Smith Machine Kneeling Glute Kickback
The Smith Machine Kneeling Glute Kickback is also known as:
- Smith Machine Donkey Kick
- Smith Machine Kneeling Rear Kick
Frequently Asked Questions
- Q: Is the Smith machine kickback better than the cable kickback?
Neither is better for everyone. The Smith machine takes plates and moves straight up and down, which makes heavier, steady loading easy, while the Cable Glute Kickback has a simpler setup and lets you choose the line of pull. Pick the one you can load progressively with clean form.
- Q: Should I kneel on a bench or on the floor?
Both versions are used. Kneeling on a bench, as shown here, raises your body so the bar and the safety stops sit higher on the rails, which helps on machines whose stops do not go low enough for a floor setup.
- Q: How heavy should I go and for how many reps?
Start with the empty bar until you can place your foot and finish each rep without arching your back, then add small plates. Most lifters use it as an accessory for about 3 sets of 10 to 15 reps per leg.
- Q: What shoes should I wear?
Wear flat shoes with a firm, grippy sole so the bar sits steadily on the arch of your foot. Socks, bare feet and soft, worn running shoes make it easier for the bar to slide.
- Q: Why do I feel this in my lower back instead of my glutes?
Usually the bar is going higher than your hip can extend, so the lower back arches to finish the rep. Lighten the load, brace your trunk and end each rep when your thigh is in line with your torso.




