Machine Lying Squat

What Is the Machine Lying Squat?
Machine Lying Squat is a compound exercise that primarily targets the quads and also engages the glutes, adductors and hamstrings. It is an intermediate-level movement performed lying flat on your back on a sliding carriage, with your shoulders under padded supports and your feet on a fixed footplate. Pressing through your feet drives the carriage, and your body with it, away from the plate against a weight stack.
The machine sits between two more familiar lifts. As on a Hack Squat, the load meets you at the shoulder pads, so the push travels up through your legs and trunk and the knees and hips bend and straighten together in a squat pattern. As on a Machine Leg Press, you lie supported and never have to balance, but here the footplate stays put and your body is what moves. Lying flat also takes your own body weight out of the lift, so the stack provides all of the resistance.
Its main use is building the quadriceps with heavy, stable work that does not depend on squat technique or balance. It usually comes after the main lower-body lift of a session, or replaces a barbell squat for lifters who cannot load one comfortably, in sets of 8 to 15 reps. Foot placement shifts the emphasis the same way it does on a leg press: feet lower on the plate increase knee bend and quad work, while feet higher increase hip bend and bring in more of the glutes and hamstrings.
It suits lifters who have learned the basic squat pattern, including experienced lifters adding quad volume around a joint or back that does not tolerate heavy free weights. If you are new to leg training, build a controlled Bodyweight Squat and a few weeks of Machine Leg Press first, so you know how deep you can bend before your pelvis starts to tuck.
Muscles Worked
- Rectus Femoris
- Primary
- Vastus Lateralis
- Primary
- Vastus Medialis
- Primary
- Gluteus Maximus
- High
- Adductor Magnus
- Medium
- Rectus Abdominis
- Minimal
- Soleus
- Minimal
Instructions
- Select a light weight on the stack and adjust the shoulder pads or footplate so your knees are bent to about 90 degrees when you lie on the carriage.
- Lie on your back on the carriage pad with your head toward the far end and settle your shoulders snugly under the shoulder pads.
- Grip the handles beside the pads and press your hips and lower back flat into the pad.
- Place your feet flat on the footplate about shoulder-width apart, toes pointing slightly out and knees in line with your toes.
- Brace your core and push through your whole foot to straighten your legs, driving the carriage away from the footplate.
- Stop when your legs are almost straight, keeping a slight bend so the knees do not snap into lockout.
- Bend your knees and hips slowly to let the carriage roll back toward the footplate, keeping your hips on the pad and heels on the plate.
- Let the stack touch down lightly without resting, then press out for the next rep.
- After the last rep, lower the carriage fully to the start before letting go of the handles and sliding out.
Common Mistakes
Hips curling off the pad
Bending deeper than your hips allow lets your pelvis roll up and your lower back round, which moves the load from your legs onto your spine.
Snapping the knees straight
Driving into a hard lockout at the top jars the knee joints and takes tension off the quads between reps.
Knees caving inward
Letting the knees drift toward each other as you push strains the inside of the knee, so keep them tracking in line with your toes.
Bouncing off the stack
Dropping the carriage so the plates crash together and rebounding out of the bottom uses momentum instead of muscle and loads the joints abruptly.
Pushing through the toes
Letting the heels lift off the footplate shifts stress to the front of the knee and reduces the glutes' share of the work.
Poorly fitted shoulder pads
Pads set too high or too loose let you slide under load and press into the collarbones instead of resting on the tops of the shoulders.
Injuries
Machine Lying Squat is a low risk exercise when performed with proper technique. The carriage runs on a fixed track, your back is supported along its length, and the weight stack settles at the bottom of every rep, so a rep you cannot finish simply lowers you back to the start.
The lower back is the most common strain point. If you bend deeper than your hip mobility allows, your pelvis curls up off the pad and your lumbar spine rounds under load, so set the machine so the stack touches down before that happens and keep your hips and lower back flat on the pad. The knees take the next most stress, especially when they cave inward or are snapped straight at the top, and the shoulder pads can press hard on the top of the shoulders and collarbones under heavy loads, so adjust them to sit snugly over the muscle rather than the bone.
Start with a light stack and a moderate range of motion, and add depth and weight only once you can keep your hips down and knees tracking over your toes. If the movement is too demanding, a Machine Leg Press or Bodyweight Wall Squat trains the same muscles without loading your shoulders and trunk; to progress, move to a Hack Squat or Machine Pendulum Squat.
Stop the set if you feel sharp pain in the knee, pain or pinching in the lower back, or numbness or tingling down the legs, and get it assessed before loading the movement again.
Frequently Asked Questions
- Q: Is the Machine Lying Squat a leg press or a squat?
It is a squat pattern done lying down. The load sits on your shoulders as in a Hack Squat and your body moves while the footplate stays fixed, whereas on a Machine Leg Press you stay still and push a platform away.
- Q: How deep should I go?
Lower until your knees are bent to about 90 degrees or slightly beyond, stopping before your hips start to lift off the pad. If the stack touches down before you reach your best depth, adjust the carriage or footplate rather than forcing extra range.
- Q: Where should I put my feet on the footplate?
Start with your feet about shoulder-width apart in the middle of the plate. Placing them lower puts more work on the quads, while placing them higher involves more glutes and hamstrings. Foot width changes comfort and depth more than which muscles work.
- Q: Is it easier on the back than a barbell squat?
Usually, because your back is supported and you never have to balance or brace a free bar. The load still passes through your trunk to the shoulder pads, though, so keep your hips flat on the pad and do not trade depth for a rounded lower back.
- Q: Can I use it instead of squats?
Yes, for building leg size and strength it works well as a squat substitute or extra quad volume. It will not train the balance, bracing and full-body coordination a free-weight Barbell Squat requires, so keep some free-weight squatting if that matters to your goals.




