Smith Machine Incline Push-Up

What Is the Smith Machine Incline Push-Up?
Smith Machine Incline Push-Up is a compound exercise that primarily targets the chest and also engages the front of the shoulders, the triceps and the core. It is a beginner-level movement in which you hold the bar of a Smith machine and press your body away from it, with your feet on the floor and your body in a straight, angled line from heels to head.
What makes this version useful is the bar itself. A Smith bar can be set at many heights in small steps, so one station gives you a whole ladder of push-up difficulties. The higher the bar, the more of your body weight rests on your feet and the easier the press; the lower the bar, the closer the movement gets to a floor Push-Up. A force-plate study of recreationally fit men and women found that push-ups with the hands raised on a 12- or 24-inch box put less peak force through the hands than a regular push-up, which is the same principle you use here when you move the bar up or down.
The chest and triceps do most of the pressing, with the front of the shoulders assisting. The serratus anterior moves the shoulder blades around the rib cage as you push, and the abs and glutes keep the body from sagging or piking. A narrower grip shifts more of the work toward the triceps, while the slightly-wider-than-shoulder-width grip shown here keeps the chest as the main mover.
This exercise suits beginners who cannot yet do floor push-ups, people returning to training and anyone who wants push-up volume without loading the wrists in a flat-palm position, since your hands wrap around a round bar. Experienced lifters also use it for high-rep chest work at the end of a session. If even a high bar setting is too hard, start with the Wall Push-Up, then lower the bar a notch at a time on your way to the Incline Push-Up on a low bench and the floor push-up.
Muscles Worked
- Pectoralis Major
- Primary
- Deltoid
- High
- Serratus Anterior
- Medium
- Gluteus Maximus
- Minimal
- Rectus Femoris
- Minimal
Instructions
- Set the Smith machine bar on its hooks at about hip height, and set the safety stops just below it. A higher bar makes the exercise easier, a lower bar makes it harder.
- Check that the bar is fully seated on the hooks, then grip it overhand with your hands slightly wider than shoulder width.
- Walk your feet back until your arms are straight, your shoulders are roughly above your hands and your body forms a straight line from head to heels.
- Brace your abs and squeeze your glutes to lock your hips in line with your shoulders and ankles.
- Bend your elbows and lower your chest toward the bar, keeping your elbows angled back about 45 degrees from your torso.
- Lower until your chest lightly touches the bar or stops about a fist's width away, keeping your head in line with your spine.
- Press through the bar to straighten your arms, moving your whole body as one unit, and stop just short of snapping the elbows into lockout.
- Repeat for the planned reps, then walk your feet forward and stand up before letting go of the bar.
Common Mistakes
Sagging hips
Letting the hips drop toward the floor arches the lower back and takes the core out of the movement, so squeeze your glutes and brace your abs to keep a straight line from head to heels.
Flaring the elbows
Elbows pointing straight out to the sides put more stress on the front of the shoulders, so angle them back about 45 degrees from your torso as you lower.
Cutting the range short
Stopping halfway down leaves most of the chest work undone, so lower until your chest is about a fist's width from the bar or lightly touches it.
Leading with the head
Dropping the chin toward the bar makes the reps look deeper than they are and strains the neck, so keep your head in line with your spine and let the chest reach the bar first.
Setting the bar too low too soon
Choosing a bar height where your hips sag or reps stall within a few repetitions trades form for difficulty, so raise the bar until you can complete every rep cleanly.
Leaning on an unsecured bar
A bar that is only partly on its hooks can slip when you twist your wrists, so check that it is fully hooked and set the safety stops right below it before you start.
Injuries
Smith Machine Incline Push-Up is a low risk exercise when performed with proper technique. Your hands carry only part of your body weight, and the bar moves on fixed rails, so most problems come from setup and posture rather than from the load itself.
The shoulders take the most strain, especially when the elbows flare straight out to the sides or when you drop the chest well below the bar at the bottom. The lower back can ache if the hips sag and the spine arches, and the elbows can feel irritated if you snap them into lockout at the top. Smith machine bars unhook with a twist of the wrists, so make sure the bar sits fully on its hooks before you lean on it, and set the safety stops directly under the bar as a backup. Wear shoes with good grip, because your feet are the anchor point and can slide on a smooth floor once the bar is set low.
To make the exercise easier, raise the bar or move your feet closer to it, or switch to the Wall Push-Up. To progress, lower the bar a notch at a time, then move to the Push-Up and eventually the Decline Push-Up. Stop the set if you feel sharp pain in the front of the shoulder, pain in the wrist or elbow, or if the bar shifts or starts to slide, and see a professional if shoulder pain keeps returning.
- Primary Focus
- Chest
- Equipment
- Smith machine and body weight
- Modality
- Strength
- Difficulty
- Beginner
Alternative Exercises
Frequently Asked Questions
- Q: How high should I set the bar?
Pick the height where you can complete about 8 to 12 controlled reps with a straight body. For most beginners that is somewhere between hip and chest height, and you can lower it one notch whenever the top of that range starts to feel easy.
- Q: When am I ready for floor push-ups?
Once you can do 12 to 15 clean reps with the bar set low, around knee height, try a set of floor Push-Ups. If the floor version still breaks down, keep training at the lowest bar height you can handle and test the floor again every week or two.
- Q: Why use a Smith machine instead of a bench or box?
A bench or box gives you only one or two heights, while a Smith bar adjusts in small steps, so you can make the exercise slightly harder each week. Gripping a round bar also keeps your wrists straighter than pressing on flat palms, which many people with sensitive wrists find more comfortable.
- Q: Is this the same as a Smith machine bench press?
No. In a Smith Machine Bench Press you lie still and move the bar, while here the bar stays fixed and your whole body moves, so your core has to hold a plank and your shoulder blades can move freely around the rib cage. The load is also limited to the share of your body weight on your hands, which makes it a good stepping stone rather than a replacement for heavy pressing.
- Q: Should the bar rest on the hooks or on the safety stops?
Either works as long as the bar cannot move under you. If you use the hooks, check that the bar is fully seated and set the safety stops directly beneath it, so the bar has nowhere to drop if it unhooks.




