Smith Machine Leg Press

What Is the Smith Machine Leg Press?
Smith Machine Leg Press is a compound exercise that primarily targets the quads and also engages the glutes, adductors and hamstrings. It is an intermediate-level movement in which you lie on your back on the floor inside a Smith machine and press the bar straight up with the soles of your feet, turning the machine into a makeshift vertical leg press.
Most gyms have a Smith machine but few have a dedicated vertical leg press, which is why lifters use this setup to get the same lying, straight-up press. The guided bar track keeps the load moving on a fixed vertical line, and because the weight travels through your feet while your back rests on the floor, nothing loads your spine from above. The bar moves straight up against its full weight, whereas a 45-degree sled such as the Machine Leg Press takes part of the load on its rails, so expect to use noticeably less weight here than on a sled.
The quads drive the press as the knees straighten, and the glutes and adductors work hardest near the bottom, where your knees come toward your chest and your hips are deeply bent. A hip-width stance suits most people; a slightly wider stance with the toes turned out often lets you reach more depth comfortably.
This variation suits lifters who already press confidently on a Machine Leg Press and know how to set the safety stops on a Smith machine. Because the bar sits on nothing but your feet, it asks for more care than any machine with a footplate, so newer lifters should build the pattern on the Machine Leg Press or the Machine Seated Leg Press first, and use the Machine Vertical Leg Press where a gym has one.
Muscles Worked
- Gluteus Maximus
- Primary
- Vastus Lateralis
- Primary
- Vastus Medialis
- Primary
- Adductor Magnus
- Medium
- Rectus Femoris
- Medium
- Rectus Abdominis
- Minimal
- Soleus
- Minimal
Instructions
- Set both safety stops at the same height, just below the lowest point you will lower the bar to, so a dropped bar stops well clear of your hips and shins.
- Load the plates evenly, unhook the bar while standing and lower it onto the safety stops.
- Lie on your back under the bar with your hips roughly beneath it and your arms flat on the floor at your sides.
- Bend your knees toward your chest and place the middle of both feet on the bar, about hip-width apart, toes pointing up and slightly out.
- Brace your core and press the bar up off the stops through your whole foot until your legs are nearly straight and vertical, without locking your knees.
- Breathe in and lower the bar slowly by bending your knees and hips, keeping your knees in line with your toes.
- Stop just before your tailbone starts to lift off the floor, keeping the bar above the safety stops.
- Exhale and press the bar straight back up to the top.
- After the last rep, lower the bar gently onto the safety stops, take your feet off it, and roll to one side before sitting up slowly.
Common Mistakes
Skipping the Safety Stops
Pressing without stops set just below your lowest depth means a slipped foot drops the whole load onto your legs and hips.
Pressing Through the Toes
Letting the bar ride toward the toes or the balls of the feet lets it roll forward and slide off, so keep it under the middle of each foot.
Letting the Pelvis Curl Off the Floor
Lowering the bar past the point where the tailbone lifts rounds the lower back with the full load directly above it.
Locking the Knees at the Top
Snapping the knees fully straight shifts the weight from the muscles onto the knee joints.
Bouncing off the Stops
Dropping the bar onto the safety stops between reps and rebounding removes control at the bottom, where the bar is most likely to shift on your feet.
Letting the Knees Cave Inward
Knees that drift inward instead of tracking over the toes put twisting stress on the knee joints and make the bar uneven on the feet.
Injuries
Smith Machine Leg Press is a medium risk exercise when performed with proper technique. The loaded bar sits directly above your body and rests on nothing but the soles of your feet, so the biggest hazard is the bar slipping off your feet or getting away from you at the bottom. The lower back is the next strain point: as the knees come toward the chest, the pelvis can curl off the floor and round the lower back under load. The knees take high loads at the bottom of a deep rep, and snapping them straight at the top puts the weight on the joint instead of the muscles.
Set both safety stops at the same height, just below the lowest point of your rep, so that a dropped bar stops well clear of your hips and shins, and test the setup with an empty bar before loading it. Wear firm, flat-soled shoes rather than soft running shoes, keep the bar under the middle of both feet, and press evenly through the whole foot. Stop each rep just before your tailbone starts to lift off the floor, keep your knees tracking over your toes, and lower the bar under control instead of dropping onto the stops.
Heavy leg presses raise blood pressure sharply, especially when you hold your breath. In a study of five experienced bodybuilders lifting to failure, the double-leg press produced the highest blood pressure of all the lifts tested, averaging a peak of 320/250 mmHg. Exhale as you press, and if you have high blood pressure, glaucoma or a heart condition, get clearance from a doctor before pressing heavy loads in this position. Sit up slowly after a set, since getting up quickly from lying with the legs raised can leave you light-headed.
To regress, learn the pattern on the Machine Leg Press or the Machine Seated Leg Press, or shorten the range and reduce the load. To progress, add weight in small steps, slow the lowering phase, or pause briefly at the bottom while your pelvis stays on the floor. Stop if your feet start to slide on the bar, or if you feel sharp pain in the lower back, knees or hips, or dizziness or a headache during the set.
- Primary Focus
- Quads
- Equipment
- Smith machine
- Modality
- Strength
- Difficulty
- Intermediate
Alternative Exercises
Other Names for the Smith Machine Leg Press
The Smith Machine Leg Press is also known as:
- Smith Machine Vertical Leg Press
Frequently Asked Questions
- Q: Is the Smith Machine Leg Press safe without a spotter?
It can be, as long as both safety stops are set just below your lowest depth so that a bar that slips off your feet lands on the stops instead of on you. Test the stop height with an empty bar first, and get a spotter if you cannot set the stops at the right height on your machine.
- Q: Should I start from the bar hooks or from the safety stops?
Starting from the safety stops is simpler, because you can unhook the bar while standing, lower it onto the stops, then lie down and press it up from there. The hooks are hard to turn while you lie under the bar, so if you do start from them, have a partner turn the bar off the hooks at the start and back on at the end.
- Q: How much weight should I use compared with a regular leg press?
Start well below your 45-degree leg press weight. On an angled sled the rails take part of the load, while a Smith bar moves straight up against its full weight, so build up from the empty bar and track this lift separately.
- Q: Where should the bar sit on my feet?
Under the middle of each foot, around the arches, with both feet about hip-width apart in firm, flat-soled shoes. A bar on the toes or the balls of the feet can roll forward and slip off as you press.
- Q: Is it a good substitute for a vertical leg press machine?
Yes, it trains the same lying, straight-up press, which is why lifters use it in gyms without a Machine Vertical Leg Press. The machine adds a fixed footplate and its own safety stops, which make it easier to set up and to keep your feet secure.




