Barbell Block Clean

Barbell Block Clean

What Is the Barbell Block Clean?

Barbell Block Clean is a compound exercise that primarily targets the glutes, quads, hamstrings and back, and also engages the calves, shoulders and core. It is an advanced-level movement in which the bar starts from a dead stop on blocks set around knee height, is pulled explosively, and is received on the front of the shoulders at the bottom of a full front squat before the lifter stands up.

Weightlifting coaches use block cleans to force an aggressive, complete finish of the pull and a fast turnover under the bar. Because the bar starts motionless with only a short distance to build speed, the lifter has to accelerate it hard from the first inch, which makes it a strong drill for explosiveness. Skipping the pull from the floor also takes load off the back and legs, so block cleans suit lighter days and lower-stress training blocks, while heavy sets let a lifter who struggles off the floor keep training the clean hard while that problem is fixed.

The block clean is a derivative of the clean, the first half of the competition Barbell Clean and Jerk, and it usually sits early in a session while the lifter is fresh, in sets of 1 to 3 reps at 70 to 100% of their best clean. Block height changes the job: higher blocks emphasize power and aggression, and lower blocks target the range around the knees where many lifters lose their back angle. Unlike the Barbell Hang Clean, there is no lowering phase to load the hips before the pull, so nothing helps the bar get moving.

The glutes, hamstrings and quads drive the explosive extension of the hips and knees, the lower back holds the torso angle off the blocks, and the traps finish the pull as the lifter drops under. The full front squat catch and the stand-up from it add heavy quad and glute work that the Barbell Power Clean and a power catch from blocks largely skip. The Barbell Block Pull trains the same starting range with heavier loads and no catch.

This is a lift for people who already clean competently. Build a sound Barbell Squat Clean, a comfortable Barbell Front Squat with high elbows and a solid Barbell Hang Clean first, then add block cleans to sharpen the finish of the pull and the speed under the bar.

Muscles Worked

MuscleActivation
Deltoid
Medium

Instructions

  1. Set two sturdy blocks of equal height and rest the loaded bar on them at about knee height, with the plates fully supported.
  2. Stand with your feet about hip-width apart, the bar over the middle of your feet, and take an overhand grip just outside your legs with straight arms.
  3. Set your hips back and above your knees, your shoulders slightly in front of the bar, your back flat and your weight over the whole foot.
  4. Push through the floor to break the bar from the blocks, keeping your arms straight and your shoulders over the bar as it slides up your thighs.
  5. As the bar reaches the upper thighs, extend your hips and knees explosively and rise onto the balls of your feet, standing up rather than driving forward.
  6. Pull your elbows up and out to keep the bar close as you drop under it, moving your feet into your squat stance.
  7. Whip your elbows forward around the bar so it lands on the front of your shoulders with your elbows high.
  8. Ride the catch down into a full front squat with your torso upright and your hips below your knees.
  9. Drive up out of the bottom immediately, keeping your elbows high, until you are standing tall.
  10. Lower the bar under control to your hips and then back onto the blocks, and reset your position before the next rep.

Common Mistakes

  • Driving the hips forward

    Shoving the hips toward the bar instead of standing up through it swings the bar away from the body and makes you jump forward to catch it.

  • Loading too heavy

    Blocks let many lifters handle big weights, but loads beyond what you can clean with good positions are where forward pulling and crashed catches start.

  • Bending the arms early

    Yanking the bar off the blocks with bent elbows wastes leg drive and slows the bar instead of letting the hips and knees accelerate it.

  • Cutting the pull short

    Dropping under before the hips and knees finish extending leaves the bar low and forces you to chase it down into the squat.

  • Low elbows in the catch

    Receiving the bar with the elbows pointing down lets it roll off the shoulders and pulls the chest forward at the bottom of the squat.

  • Uneven or unstable blocks

    Blocks of different heights or a bar resting on their edges tilts the start position and lets the bar shift as you set up.

Injuries

Barbell Block Clean is a medium risk exercise when performed with proper technique. The wrists, elbows and shoulders take the bar in the front rack, the knees and hips absorb it at the bottom of a full squat, and the lower back has to hold its position as the bar breaks from the blocks. Loading the bar beyond what you can clean with good positions is the most common route to trouble, because it pulls you forward off the blocks and turns the catch into a crash.

The blocks themselves add a hazard. Use solid lifting blocks of equal height, set so the plates rest fully on them, and lower the bar back to them under control after each rep. If you miss, push the bar forward and step back so it lands on the platform clear of the blocks, since a bar that hits a block edge can bounce in an unpredictable direction. Hollow plyo boxes are not built to take a dropped loaded barbell.

If the front rack is uncomfortable, work on wrist, lat and triceps mobility with the Barbell Front Squat before loading this lift. To regress, use the Barbell Hang Clean for the turnover, the Barbell Block Pull for the starting position, or the Barbell Power Clean if the full squat catch is the limit. To progress, lower the blocks gradually toward the floor and the full Barbell Squat Clean.

Stop the set if you feel sharp pain in the wrist, elbow, shoulder, lower back or knee, if you cannot get the elbows up into the rack, or if the bar keeps crashing onto your shoulders or pulling you forward in the squat.

Frequently Asked Questions

Q: Should a block clean be caught in a full squat or a power position?

This version is caught in a full front squat, which lets you receive heavier weights and trains the stand-up; catching above parallel turns it into a block power clean. In a study of 10 collegiate athletes cleaning 90% of their power clean max from a static start at knee height, the full squat catch absorbed more than twice the work of a power catch.

Q: How high should the blocks be?

Knee height is the most common setting and a sensible place to start. Higher blocks emphasize power and an aggressive finish, while blocks just below the knee train the range where many lifters lose their back angle.

Q: What is the difference between a block clean and a hang clean?

A block clean starts from a dead stop on the blocks, while a Barbell Hang Clean is lifted from the floor and lowered to the start height first, which loads the hips before the pull. The block version makes you accelerate the bar with no help from that stretch.

Q: Can I use plyo boxes instead of lifting blocks?

Only if they are sturdy, the same height and you lower the bar onto them under control. Most plyo boxes are hollow and not built to take a dropped loaded barbell, so on a missed rep the bar should go forward onto the platform, not onto the boxes.

Q: Is it normal to clean more from blocks than from the floor?

It happens, because knee-height blocks let some lifters start in a stronger position and skip a part of the pull they handle poorly. A large gap usually points to a technical or strength problem in the pull from the floor, which the Barbell Clean Deadlift can help address.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.