Barbell Skull Crusher (Reverse Grip)

Barbell Skull Crusher (Reverse Grip)

What Is the Barbell Skull Crusher (Reverse Grip)?

Barbell Skull Crusher (Reverse Grip) is an isolation exercise that primarily targets the triceps and also engages the forearm flexors, which work to hold the underhand grip. It is an intermediate-level movement in which you lie on a flat bench, hold a barbell with your palms facing toward your head, and lower it toward your forehead by bending only at the elbows. It is the underhand version of the Barbell Skull Crusher.

Like the overhand version, it builds triceps size and lockout strength for pressing, and it usually sits after the main pressing work of a session as an accessory. Because the upper arms point up and slightly back, the long head of the triceps, which also crosses the shoulder, works at a longer length than it does in a pushdown with the arms at your sides.

The reverse grip is often described as a way to shift the work onto one head of the triceps, and coaching sources disagree on which head that is. All three heads attach to the same tendon at the point of the elbow and none of them turns the forearm, so the upper-arm angle, not the direction of the palms, is what changes the balance between them. What the underhand grip really changes is the hold: the bar sits nearer the fingers, the wrists tend to bend back, and the forearm flexors work harder to keep the bar secure. Most lifters use less weight here than on the overhand version for that reason.

It suits lifters who already control the overhand skull crusher well and want a variation that also challenges the grip. A straight bar asks the forearms to turn fully palms up, so anyone who cannot hold that position comfortably should stay with the Barbell Skull Crusher or the Dumbbell Lying Triceps Extension. The Cable Triceps Pushdown (Reverse Grip) is a steadier way to get used to the underhand grip before taking it over your face.

Muscles Worked

MuscleActivation

Instructions

  1. Sit on the end of a flat bench with the barbell resting on your thighs.
  2. Take an underhand grip with your hands about shoulder-width apart and your thumbs wrapped around the bar.
  3. Lie back with your head, upper back and hips on the bench and your feet flat on the floor, bringing the bar to your chest.
  4. Press the bar up until your arms are straight above your shoulders, palms facing toward your head.
  5. Tilt your upper arms slightly back toward your head so your elbows point up, and keep your wrists straight with the bar low in your palms.
  6. Keep your upper arms still and bend only at the elbows to lower the bar slowly toward your forehead.
  7. Stop just above your forehead, with your elbows about shoulder-width apart and pointing up.
  8. Extend your elbows to press the bar back to the start without snapping them straight.
  9. Repeat for the target reps, then bring the bar to your chest and down to your thighs as you sit up.

Common Mistakes

  • Using a thumbless grip

    Leaving the thumbs off the bar lets it roll out of the fingers and over the face, so always wrap them around it.

  • Bending the wrists back

    Letting the bar sink toward the fingertips bends the wrists back, strains them and loosens the hold.

  • Copying the overhand weight

    The underhand grip is harder to hold, so starting at your overhand skull crusher load usually costs control on the way down.

  • Flaring the elbows

    Letting the elbows drift wider than the hands moves stress onto the elbow joint and away from the triceps.

  • Letting the upper arms swing

    Moving the upper arms toward the feet turns the lift into a pullover and press instead of an elbow extension.

  • Lowering too fast

    Dropping the bar quickly toward the forehead loads the elbows hard at the bottom and leaves little margin if the grip slips.

Injuries

Barbell Skull Crusher (Reverse Grip) is a medium risk exercise when performed with proper technique. The elbows take the most stress, followed by the wrists, and because the bar travels above your face, a loosening grip is the hazard that sets this version apart from the overhand one.

Pain at the back of the elbow usually comes from a load that is too heavy, a fast descent or elbows drifting out. The underhand grip adds wrist strain when the bar rolls toward the fingers and bends the wrists back, and a straight bar forces the forearms fully palms up, which some lifters feel in the wrist or the inside of the elbow.

Wrap your thumbs around the bar, keep your wrists straight over your forearms, start lighter than your overhand load and lower the bar slowly. Do it after your pressing work so the elbows are warm, and use a spotter for heavy or unfamiliar loads. If the grip bothers your wrists, go back to the Barbell Skull Crusher or a Dumbbell Lying Triceps Extension, which lets the wrists settle at their own angle. Progress by adding reps or slowing the descent before adding weight.

Stop the set if you feel sharp pain at the back of the elbow or in the wrist, or if the bar starts slipping toward your fingertips. A pop, swelling or sudden weakness at the elbow should be checked by a clinician.

Frequently Asked Questions

Q: Does the reverse grip target a different triceps head?

Not in any reliable way. All three heads attach to the same tendon at the elbow and none of them rotates the forearm, so the upper-arm angle matters far more than the direction of your palms. The main change is extra work for the grip and forearms.

Q: How much weight should I use compared with the regular skull crusher?

Start lighter than your Barbell Skull Crusher load. The underhand grip is harder to hold and puts the wrists in a less stable position, so build reps and control first, then add weight in small steps.

Q: Can I do this with an EZ bar?

Yes. The angled grips of an EZ bar let the forearms stay partly turned instead of fully palms up, which many lifters find easier on the wrists.

Q: Should the bar touch my forehead?

No. Stop a short distance above your forehead so the triceps keep the load and you keep a safety margin, which matters more here because the underhand grip is less secure.

Q: Why do my wrists hurt with the reverse grip?

Usually the bar has rolled toward your fingers and bent the wrists back, or the straight bar is asking for more forearm rotation than you have. Keep the bar low in your palms with straight wrists, use a lighter load or switch to an EZ bar, and see a clinician if the pain persists.

Q: Where should it go in a workout?

After your main pressing lifts, as triceps accessory work, with moderate loads for about 8 to 15 reps per set.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.