Machine Leg Press (Wide Stance)

Machine Leg Press (Wide Stance)

What Is the Machine Leg Press (Wide Stance)?

Machine Leg Press (Wide Stance) is a compound exercise that primarily targets the quadriceps and also engages the glutes, the adductors and, to a lesser degree, the hamstrings. It is a beginner-level movement performed on a 45-degree plate-loaded sled, with the feet set wider than shoulder width near the outer edges of the platform and the toes turned slightly out.

Like every leg press, it lets you load the knee and hip extensors heavily while the backrest supports the torso and the sled fixes the path, so balance and spinal loading limit the set far less than they do in a squat. That makes it a common main or secondary lower-body movement in hypertrophy and general strength programs, usually placed after squats or as a substitute for them when a lifter needs to train hard around a back or balance limitation.

A wide stance is often said to move the work from the quads to the glutes and inner thighs, but the leg press evidence does not show that. In a study of 28 trained men and women on an inclined leg press, setting the feet at 150% of hip width produced no difference in vastus medialis, vastus lateralis, rectus femoris or gluteus medius activity compared with a hip-width stance. The glute max and adductors were not measured, and the claims about them come from squat research rather than the leg press. What the wide stance clearly changes is hip position: the thighs open outward and the knees travel out over the turned-out toes, which gives the thighs room beside the torso at the bottom of the rep.

The wide stance suits lifters who find a hip-width stance cramped, whose knees run into the torso before they reach full depth, or who simply prefer the feel of a turned-out position. For most people it trains the legs much like the standard Machine Leg Press or the Machine Leg Press (Narrow Stance), so choose the width that lets your knees track over your toes and your pelvis stay on the seat. If inner-thigh strength is the goal, add direct work such as the Machine Hip Adduction. Beginners can build the pattern first with the Dumbbell Goblet Squat or a light leg press before loading the sled heavily.

Muscles Worked

MuscleActivation
Soleus
Minimal

Instructions

  1. Load the sled with plates and sit with your back and head flat against the backrest and your hips settled into the seat.
  2. Place your feet on the platform wider than shoulder width, near its outer edges, with your toes turned slightly out and your whole foot flat.
  3. Press the platform up a few inches, release the safety catches and hold the handles at the sides of the seat.
  4. Start with your legs extended and a slight bend in your knees.
  5. Inhale and lower the platform by bending your knees and hips, letting your knees travel out in line with your toes.
  6. Stop when your thighs come close to the sides of your torso, before your hips start to lift off the seat.
  7. Exhale and press through your whole foot to drive the platform back up, keeping your knees tracking over your toes.
  8. Finish with your knees almost straight, without snapping them back, and begin the next rep.
  9. After the last rep, extend your legs, re-engage the safety catches and only then take your feet off the platform.

Common Mistakes

  • Letting the knees cave in

    The knees drift inside the line of the turned-out feet as you press, twisting the knee joint under load instead of tracking out over the toes.

  • Setting the feet too wide

    A stance wider than your hips comfortably allow rolls the feet onto their inner edges and stops the knees from following the toes.

  • Lowering until the pelvis tucks

    Going deeper than your hips allow lifts the pelvis off the seat and rounds the lower back under the full weight of the sled.

  • Snapping the knees into lockout

    Driving hard into a straight-legged finish lets the knees hyperextend under a heavy load instead of stopping with a slight bend.

  • Pushing through the toes

    Letting the heels lift off the platform shifts pressure onto the balls of the feet and the front of the knees instead of pressing through the whole foot.

  • Removing the feet with the catches open

    Taking the feet off the platform before the safety catches are re-engaged leaves nothing to stop the sled from sliding down.

Injuries

Machine Leg Press (Wide Stance) is a low risk exercise when performed with proper technique. The backrest supports the torso and the sled runs on a fixed track, but the loads used are heavy, so the problems that do occur come from depth, knee control and the setup rather than from losing balance.

The lower back is the most common strain point. Lowering the sled past the point where the pelvis stays on the seat makes the hips roll up and the lumbar spine round under the full load. Find the deepest position you can reach with your hips and lower back flat against the pad and stop there; lowering the backrest angle or moving the feet slightly higher can buy range for lifters who tuck early. At the top, snapping the knees back into hyperextension under a heavy sled stresses the knee joint, so finish each rep with a slight bend.

The wide stance adds demands at the hip and groin. The knees should travel out in line with the turned-out toes; letting them collapse inward twists the knee under load. A stance wider than your hips allow can strain the adductors or cause a pinch at the front of the hip at the bottom. Bring the feet in or turn the toes out less if that happens, and switch to the Machine Leg Press with a hip-width stance or a shorter range if the pinch persists.

Start light enough to own the bottom position, then add load gradually. A Glute Bridge or Dumbbell Goblet Squat is a gentler place to start for anyone returning from a back or knee problem. Always re-engage the safety catches before taking your feet off the platform, and stop the set if you feel sharp pain in the knee, groin, hip or lower back.

Other Names for the Machine Leg Press (Wide Stance)

The Machine Leg Press (Wide Stance) is also known as:

  • Sumo Leg Press

Frequently Asked Questions

Q: Does a wide stance on the leg press work the inner thighs more?

It has not been shown on the leg press, because the studies comparing stance widths did not measure the adductors. The adductor magnus helps extend the hip on every leg press, whatever the width, so if inner-thigh strength is a real goal, add direct work such as the Machine Hip Adduction.

Q: Is the wide-stance leg press better for the glutes?

There is no leg press evidence that it is, since glute max activity has not been compared across stance widths on this machine. Whatever the width, use the full range you can reach with your pelvis still on the seat, and for direct glute work a hip-dominant exercise such as the Barbell Hip Thrust is the better choice.

Q: How wide should my feet be?

Start just wider than shoulder width with the toes turned slightly out, and widen only as far as you can keep the whole foot flat and the knees tracking over the toes. If the feet roll onto their inner edges or the front of the hip pinches at the bottom, bring them back in.

Q: Should I use a wide or a narrow stance on the leg press?

Either works the quadriceps hard, and the inclined leg press research found the same quadriceps activity with the feet at hip width and at 150% of hip width. Pick the width that is comfortable for your hips and lets you reach a full range with your pelvis on the seat, or rotate between this and the Machine Leg Press (Narrow Stance) for variety.

Q: How deep should I lower the platform?

Lower it until your thighs come close to the sides of your torso, but stop at the point where your hips would start to roll off the seat. That point differs between lifters, so set your depth by the pelvis, not by a fixed knee angle.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.