Machine Reverse Hack Squat

Machine Reverse Hack Squat

What Is the Machine Reverse Hack Squat?

Machine Reverse Hack Squat is a compound exercise that primarily targets the glutes and quads and also engages the adductors, hamstrings and lower back. It is an intermediate-level movement performed on a plate-loaded hack squat machine with you facing the back pad instead of leaning against it, so your hips can travel back and your torso can lean forward as you squat down.

The machine fixes the path of the load, so you can train hard and close to failure without balancing a barbell or worrying about the bar drifting forward. That makes it a common choice in muscle-building programs, either as the main squat of a leg day or as a second lower body movement after a free weight squat or deadlift, usually for moderate to higher rep sets.

Turning around changes the work compared with the standard Hack Squat. With your back on the pad, the torso stays upright and the knees do most of the work, which keeps the standard version quad-focused. Facing the pad lets the hips fold and sit back, so the glutes and the adductor magnus take a larger share of the effort, while the deep knee bend still loads the quads heavily. How far you sit back steers the balance: a more forward lean favors the glutes, and a more upright torso with the knees traveling forward keeps more of the work on the quads. For a quad-focused machine option, the Machine Pendulum Squat is the closer fit.

It suits lifters who want a glute-heavy squat with machine stability and those who find a loaded barbell on the back uncomfortable. Because your lower back is not supported by the pad, you should be able to brace and hold a neutral spine in a squat before loading it. If it is too hard, build the pattern with the Dumbbell Goblet Squat and the standard Hack Squat first. Thinking about pushing the platform away and driving the hips forward out of the bottom helps you feel the glutes doing their share.

Muscles Worked

MuscleActivation

Instructions

  1. Load the plates onto the machine and, if the shoulder pads adjust, set them at a height you can get under with your knees slightly bent.
  2. Step onto the footplate facing the back pad, set the shoulder pads on top of your shoulders and grip the handles at the front of the pads.
  3. Place your feet about hip-width apart with your toes turned slightly out and your whole foot flat on the platform.
  4. Stand up to lift the sled, release the safety lock if the machine has one and start standing tall with your knees soft.
  5. Brace your core, then push your hips back and bend your knees, letting your torso lean forward toward the pad while your back stays neutral.
  6. Lower until your hip crease is at or below your knees, or until just before your lower back starts to round.
  7. Drive through your whole foot to push the sled up, straightening your hips and knees together and keeping your knees in line with your toes.
  8. Finish standing tall without leaning back, then repeat for the planned reps.
  9. Re-engage the safety lock after the last rep before stepping off.

Common Mistakes

  • Rounding the lower back at the bottom

    Letting the pelvis tuck under as you reach depth loads the spine in a rounded position, so stop the descent just above the point where this happens.

  • Overarching at lockout

    Leaning back and pushing the hips forward to finish the rep arches the lower back under the shoulder pads, so stand tall with your ribs down and glutes squeezed instead.

  • Heels lifting off the platform

    Rising onto the toes shifts pressure onto the front of the foot and the knees, so keep the whole foot planted and move your feet if the heels keep coming up.

  • Knees caving inward

    Letting the knees collapse toward each other as you drive up stresses the inside of the knee, so push them out in line with your toes.

  • Bouncing out of the bottom

    Dropping fast and rebounding off the deepest position puts sudden load on the knees and lower back, so lower under control and drive up smoothly.

  • Staying too upright

    Keeping the torso vertical as if your back were on the pad turns the movement back into a quad-dominant squat and removes the hip bias that is the reason to face the pad.

Injuries

Machine Reverse Hack Squat is a medium risk exercise when performed with proper technique. The machine guides the path of the load, but the shoulder pads press down through your spine while your torso leans forward with nothing supporting your lower back, and the bottom position takes your hips and knees into deep flexion under load.

The lower back is the most common strain point. It tends to round as you reach the bottom and your pelvis tucks under, or to overarch as you lock out at the top. The knees can also become irritated by heavy loads, bouncing out of the bottom or letting them cave inward, and the shoulder pads can press uncomfortably on the neck if they are set too low. Brace your core before every rep, lower under control, stop just above the depth where your lower back starts to round, keep your whole foot planted and finish each rep standing tall rather than leaning back.

If you cannot hold a neutral spine, regress to the standard Hack Squat, where the pad supports your back, or to the Machine Leg Press. The Machine Belt Squat takes the load off the spine entirely while still training the squat. Progress by adding load gradually, pausing at the bottom or slowing the lowering phase rather than chasing depth you cannot control.

Stop the set if you feel sharp pain in your lower back, pain or numbness that travels down a leg, pain inside the knee joint, or a pinching sensation at the front of the hip in the bottom position.

Frequently Asked Questions

Q: Does the reverse hack squat work the glutes or the quads more?

Both work hard, and the split depends on your torso angle. A lab study of healthy adults doing back squats found the hips did more of the work than the knees once the torso leaned further forward than the shins, so on this machine, sitting your hips back and letting your chest come toward the pad should shift more of the work to the glutes, while a more upright torso keeps more of it on the quads.

Q: How is it different from the regular hack squat?

On the standard Hack Squat your back rests on the pad and your knees do most of the work. Facing the pad lets your hips travel back and your torso lean forward, which brings the glutes and adductors in more, but your lower back is no longer supported and has to hold its position on its own.

Q: How deep should I go?

Go as deep as you can while keeping your lower back neutral and your heels down, which for most people puts the hip crease at or below the knees. Stop just above the point where your pelvis starts to tuck under.

Q: Where should I place my feet?

Start with your feet about hip-width apart in the middle of the platform and your toes turned slightly out, then adjust until your heels stay down and your knees track over your toes at the bottom. Footplate angles and pad positions vary between machines, so the best spot differs from one machine to the next.

Q: Is the reverse hack squat good for beginners?

It can be, but the unsupported lower back makes it harder to learn than the standard hack squat or the Machine Leg Press. Most beginners do better building the squat pattern with the Dumbbell Goblet Squat and the Hack Squat first.

Q: Can it replace hip thrusts?

Not fully. The reverse hack squat loads the glutes hardest near the bottom, where they are stretched, while the Barbell Hip Thrust loads them hardest at full hip extension, so the two complement each other in a glute-focused program.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.