Smith Machine Bench Press (Wide Grip)

Smith Machine Bench Press (Wide Grip)

What Is the Smith Machine Bench Press (Wide Grip)?

Smith Machine Bench Press (Wide Grip) is a compound exercise that primarily targets the chest and also engages the front of the shoulders and the triceps. It is an intermediate-level movement that pairs the guided bar of the Smith Machine Bench Press with a grip set well outside shoulder width.

Widening the grip changes how the press is shared out. With the hands farther apart, the elbows bend less at the bottom of each rep, so the triceps contribute less and the chest and front deltoids carry a larger share of the lift. A study of 28 men pressing a free barbell found that a wide grip produced chest activity similar to a medium grip but lower triceps activity, and the six-rep max was the same with both grips. The wide grip also shortens the distance the bar travels from lockout to chest, which is why it suits chest-focused hypertrophy work more than triceps strength.

The Smith machine adds a fixed vertical bar path and hooks that can be engaged at any point. That removes the balancing work of a free barbell, so lifters can push sets closer to failure with less risk of losing the bar, which is useful for bodybuilding-style chest training and for people training alone. The trade-off is that the bar cannot drift to suit your shoulders, so the bench position decides where the bar lands on your chest, and a poor setup is felt rep after rep.

The movement fits best as a main or secondary chest press in a hypertrophy session, usually after heavier free-weight pressing or in place of it. It suits lifters who already press comfortably with a standard grip and have pain-free shoulder mobility. Those still learning to press should start with the standard Smith Machine Bench Press or the Dumbbell Bench Press, and anyone whose shoulders object to a wide grip can shift emphasis to the triceps with the Smith Machine Bench Press (Close Grip) instead.

Muscles Worked

MuscleActivation

Instructions

  1. Place a flat bench inside the Smith machine so that, when you lie down, the bar sits over your lower chest. Set the safety stops just below the height where the bar will touch your chest.
  2. Lie back with your head, upper back and glutes on the bench and your feet flat on the floor.
  3. Grip the bar overhand with your hands well outside shoulder width, about one and a half times shoulder width, with your thumbs wrapped around the bar and your wrists stacked over your elbows.
  4. Squeeze your shoulder blades back and down into the bench.
  5. Straighten your arms and twist the bar to release it from the hooks.
  6. Lower the bar under control to your lower chest, letting your elbows travel out to the sides and slightly toward your hips.
  7. Touch the chest lightly without bouncing, with your forearms close to vertical.
  8. Press the bar straight up until your arms are straight, keeping your shoulder blades pinned to the bench.
  9. After the last rep, twist the bar back onto the nearest hooks before letting go.

Common Mistakes

  • Grip far wider than needed

    Spreading the hands past about twice shoulder width adds shoulder strain and shortens the press without giving the chest more useful work.

  • Bench in the wrong spot

    Because the bar only moves straight up and down, a bench placed too far toward the head brings the bar down onto the upper chest or neck instead of the lower chest.

  • Elbows flared straight out

    Letting the upper arms sit at a right angle to the torso at the bottom loads the front of the shoulder, so angle the elbows slightly toward your hips.

  • Losing the shoulder blade set

    Letting the shoulders roll forward off the bench as you press removes a stable base and pushes more load into the shoulder joint.

  • Bouncing the bar off the chest

    Dropping the bar and rebounding it skips the controlled bottom position where the chest and shoulders are most exposed.

  • Skipping the safety stops

    Training to failure without stops set just below chest height leaves you relying on twisting the hooks back into place while exhausted.

Injuries

Smith Machine Bench Press (Wide Grip) is a medium risk exercise when performed with proper technique. The guided bar and safety hooks make it hard to lose control of the weight, but the wide hand position places more demand on the shoulders than a standard grip, and the fixed bar path cannot adjust if the bench is set in the wrong place.

The front of the shoulder and the joint at the outer end of the collarbone take most of the strain, along with the chest tendon at the bottom of each rep. A 2024 modeling study of ten experienced lifters estimated that widening the grip from 1.5 to 2 times shoulder width raised the forces on both of those joints, while pulling the shoulder blades back lowered them. It used a light bar and measured joint loads rather than injuries, so it is a reason to keep the grip moderately wide and the shoulder blades set, not evidence that a wide grip causes harm on its own.

To keep the load manageable, place the bench so the bar touches the lower chest rather than the upper chest or neck, keep the shoulder blades squeezed back and down, lower the bar under control and set the safety stops just below the height where the bar meets your chest. If a wide grip bothers your shoulders, bring the hands in toward a standard Smith Machine Bench Press grip or switch to the Dumbbell Bench Press, where the hands can turn and the path can adapt. Once the movement is comfortable, the Barbell Bench Press (Wide Grip) is the free-weight progression.

Stop the set if you feel sharp pain at the front or top of the shoulder, a pulling or tearing sensation in the chest or armpit, or numbness or tingling down the arm. Painful clicking in the shoulder that repeats each rep is also a reason to end the set and narrow the grip next time.

Frequently Asked Questions

Q: How wide should my grip be?

Start with the hands clearly outside your usual bench grip, around one and a half times shoulder width, and adjust so your forearms are close to vertical when the bar touches your chest. Going much wider than twice shoulder width mostly adds shoulder load.

Q: Does a wide grip work the chest more than a standard grip?

Not by much. The bigger change is that the triceps do less and the bar travels a shorter distance, so the chest and front shoulders handle a larger share of the press.

Q: Can I lift as much with a wide grip?

Most lifters handle about the same load as with their standard grip and more than with a close grip. If your numbers drop sharply, your grip is probably wider than your shoulders tolerate.

Q: Is it safe to do without a spotter?

Yes, provided you set the safety stops just below the height where the bar touches your chest. If you fail a rep, lower the bar onto the stops or twist it back onto the nearest hooks.

Q: How is it different from the wide-grip barbell bench press?

The Smith machine fixes the bar on a vertical track, so you skip the balancing work and can train closer to failure alone. The Barbell Bench Press (Wide Grip) lets the bar path adapt to your shoulders and trains more stabilizing control.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.