Smith Machine Incline Bench Press (Close Grip)

What Is the Smith Machine Incline Bench Press (Close Grip)?
Smith Machine Incline Bench Press (Close Grip) is a compound exercise that primarily targets the triceps and also engages the upper chest and front shoulders. It is an intermediate-level movement performed on an incline bench set inside a Smith machine, with the hands about shoulder width apart or slightly closer and the elbows kept close to the body.
Narrowing the grip turns the incline press into a strong triceps builder. A study of strength-trained adults on the barbell bench press found that a narrower grip raised the load on the elbow extensors and the activity of the lateral triceps, front deltoid and upper chest, while a wider grip shifted more work to the lower chest. The incline adds to that upper chest and front shoulder emphasis, so this variation sits between a triceps press and an upper chest press.
The Smith machine guides the bar along a fixed track, which takes balance out of the lift and lets the lifter focus on pressing. Adjustable safety stops make it practical to push sets close to failure without a spotter. Because the triceps tire before the chest, most lifters handle noticeably less weight here than on the regular Smith Machine Incline Bench Press.
It fits bodybuilders and general lifters who want more triceps and upper chest work from one press, and lifters who use close-grip pressing to support their bench press lockout. It usually sits after the main chest press of a session or as the first movement of an arm day. Lifters new to pressing should first get comfortable with the flat Smith Machine Bench Press (Close Grip) and the standard incline press before narrowing the grip at an incline.
Muscles Worked
- Deltoid
- High
- Pectoralis Major
- High
- Biceps Brachii
- Minimal
Instructions
- Set an adjustable bench to an incline of 30 to 45 degrees and position it inside the Smith machine so the bar lines up over your upper chest.
- Set the safety stops just below the height of your chest when lying on the bench.
- Sit back on the bench with your head, upper back and hips against the pad and your feet flat on the floor.
- Grip the bar overhand with your hands about shoulder width apart or slightly narrower, keeping the bar low in your palms and your wrists straight.
- Press the bar up and rotate it to release it from the machine's hooks, holding it with your arms extended above your shoulders.
- Inhale and lower the bar slowly to your upper chest, just below your collarbones, keeping your elbows tucked close to your sides.
- Touch the chest lightly without bouncing, with your wrists stacked over your elbows.
- Exhale and press the bar back up until your elbows are fully extended.
- Repeat for the desired number of repetitions, then rotate the bar to lock it back onto the hooks.
Common Mistakes
Grip too narrow
Placing the hands close enough to touch bends the wrists back and strains the elbows without adding much triceps work.
Flaring the elbows
Letting the elbows drift out wide turns the lift back into a regular incline press and pushes stress into the front of the shoulders.
Bench in the wrong spot
With the bench too far forward or back, the fixed bar lands on the neck or the lower chest instead of the upper chest.
Bending the wrists back
Holding the bar high in the fingers lets the wrists fold back under load instead of staying stacked over the forearms.
Cutting the range short
Stopping several inches above the chest skips the stretched portion of the rep where the triceps and upper chest work hardest.
Skipping the safety stops
Training without the stops set just below the bottom position leaves no protection if a rep fails near the chest.
Injuries
Smith Machine Incline Bench Press (Close Grip) is a medium risk exercise when performed with proper technique. The wrists, elbows and the front of the shoulders take most of the stress. A grip with the hands nearly touching bends the wrists back and twists the elbows, and letting the elbows flare wide at the bottom pushes the load into the front of the shoulder.
Keep the hands about shoulder width apart or just inside it, the bar low in the palm and the wrists stacked over the elbows. Place the bench so the bar touches the upper chest below the collarbones, since the fixed track cannot adjust to a bench that sits too far forward or back. Set the safety stops just below the lowest point of the rep and use a load you can lower under control.
If the elbows or wrists ache, regress to the standard-grip Smith Machine Incline Bench Press or a Dumbbell Press (Close Grip), which lets the wrists find their own angle. Lifters who feel pain at the top of the shoulder often do better with a slightly wider grip. Progress by adding small increments of load or a pause on the chest before moving to the free-weight Barbell Incline Bench Press (Close Grip).
Stop the set if you feel sharp pain in the shoulder, elbow or wrist, or any pinching at the front of the shoulder, and seek professional advice if it persists.
- Primary Focus
- Triceps
- Equipment
- Smith machine and bench
- Modality
- Strength
- Difficulty
- Intermediate
Alternative Exercises
Frequently Asked Questions
- Q: How is this different from the flat close-grip Smith machine bench press?
Both are triceps-focused presses, but the incline moves more of the chest work to the upper chest and brings the front shoulders in harder. The flat Smith Machine Bench Press (Close Grip) usually allows more weight, while the incline version suits lifters who want triceps and upper chest work from one movement.
- Q: What bench angle should I use?
Most lifters set the bench at 30 to 45 degrees. A study of 30 trained adults on a free-weight barbell bench press at a standard grip found upper chest activity peaked at a 30 degree incline, front shoulder activity was highest at the steepest angle, and triceps activity stayed about the same at every angle. A lower incline keeps more of the chest involved, while a steep one turns the press toward the shoulders.
- Q: How close should my hands be?
About shoulder width apart or slightly narrower is enough to shift the work toward the triceps. Going closer than that mostly strains the wrists and elbows without adding much triceps work.
- Q: Should I use less weight than on the regular incline press?
Yes. The narrow grip makes the triceps the limiting muscle, so expect to lift noticeably less than on the standard-grip Smith Machine Incline Bench Press and choose a load you can lower with control to the chest.
- Q: Where should the bar touch?
The bar should touch the upper chest, just below the collarbones. Set the bench before you load the bar so the fixed track lines up with that spot, since you cannot adjust the bar path mid-set.




