Smith Machine Incline Shoulder Raise

Smith Machine Incline Shoulder Raise

What Is the Smith Machine Incline Shoulder Raise?

Smith Machine Incline Shoulder Raise is an isolation exercise that primarily targets the chest, specifically the serratus anterior along the side of the rib cage, and also engages the pectoralis major, front deltoids and trapezius. It is a beginner-level movement in which you lie on an incline bench, hold the Smith bar at arm's length with locked elbows, and lift the bar a few inches by pushing your shoulder blades forward and off the bench.

The movement is scapular protraction, not a press. The elbows never bend, so the only thing that moves the bar is the shoulder blades gliding around the rib cage. That is exactly the job of the serratus anterior, which holds the shoulder blade flat against the ribs and rotates it upward as the arm rises. A weak or poorly controlled serratus is the usual cause of the shoulder blade lifting away from the ribs, known as winging, which is why this muscle features so heavily in shoulder health and rehab programs.

The incline matters. With the torso inclined and the arms vertical, the arms sit above shoulder height relative to the body, so the shoulder blade has to stay rotated upward while it protracts. An EMG study of 20 healthy adults found that exercises holding the shoulder blade upwardly rotated while accentuating protraction, such as the push-up plus and the dynamic hug, drew the most serratus anterior activity of the eight exercises tested. The Smith machine adds a fixed bar path and safety stops, so you can load the movement without having to balance a free bar overhead.

The exercise suits lifters who press a lot and want to build the shoulder blade control that sits under the Barbell Incline Bench Press, as well as anyone working on shoulder blade stability. It is usually done near the end of a chest or shoulder session, or as part of a warm-up with a light load. If the bar is too heavy to move without shrugging or bending the elbows, start with the bodyweight Scapular Retraction and Protraction or the Serratus Wall Slide before loading the bar.

The mind-muscle connection genuinely matters here, because the range of motion is only a few inches and it is easy to let the upper traps or the triceps do the work. Think of reaching the bar toward the ceiling with your shoulder blades sliding around your ribs, not up toward your ears.

Muscles Worked

MuscleActivation
Deltoid
Medium

Instructions

  1. Set an adjustable bench to a moderate incline of about 30 to 45 degrees and place it inside the Smith machine so the bar lines up over your shoulders.
  2. Set the safety stops just below where the bar will sit with your arms straight and your shoulder blades flat on the bench.
  3. Lie back on the bench with your feet flat on the floor and your head, upper back and hips on the pad.
  4. Grip the bar with an overhand grip about shoulder-width apart, straighten your arms and rotate the bar to unhook it.
  5. Hold the bar directly above your shoulders with your arms vertical and your elbows locked but not forced past straight.
  6. Let your shoulder blades settle back into the bench so the bar drops slightly. This is the start position.
  7. Exhale and push the bar toward the ceiling by sliding your shoulder blades forward and off the bench, keeping your elbows straight and your shoulders away from your ears.
  8. Pause for a second at the top with the shoulder blades fully forward.
  9. Inhale and lower the bar slowly until your shoulder blades are flat against the bench again.
  10. Repeat for the desired reps, then rotate the bar to hook it back on the rack.

Common Mistakes

  • Shrugging toward the ears

    Lifting the shoulders up toward the ears lets the upper traps take over, so push the shoulder blades forward around the ribs instead.

  • Bending the elbows

    Letting the elbows bend turns the rep into a partial incline press for the triceps and chest, so keep the arms locked from start to finish.

  • Cutting the range short

    Stopping before the shoulder blades are fully forward skips the top of the movement, where the serratus works hardest.

  • Lifting the head and chest

    Peeling the upper back off the bench or craning the neck makes the bar rise without any shoulder blade movement, so keep your head and spine on the pad.

  • Dropping into the bottom

    Letting the bar fall back to the start position loses control of the shoulder blades, so lower it slowly until they settle flat against the bench.

  • Loading too heavy

    A load you cannot move with straight arms and a still torso forces compensation, so use a weight you can control for 10 to 15 smooth reps.

Injuries

Smith Machine Incline Shoulder Raise is a low risk exercise when performed with proper technique. The elbows stay locked, the range of motion is short and the Smith machine guides the bar, so the load on any one joint is modest. The usual trouble spots are the neck and upper traps when you shrug instead of protract, the elbows when you snap them into hyperextension under the bar, and the front of the shoulder if you let the bar drift toward your face and the shoulders roll forward at the top.

Set the safety stops just below the bottom position, where the bar sits with your shoulder blades back on the bench and your arms straight. Because the bar travels only a few inches, this means a missed rep or a slipped grip lands on the stops instead of your face or chest. Choose a load you can move for 10 to 15 slow reps with a pause at the top, keep the elbows straight but not forced past straight, and keep your head and upper back on the bench as the shoulders rise.

If you cannot move the bar without shrugging, regress to the bodyweight Scapular Retraction and Protraction or the Serratus Wall Slide. To progress, add load in small steps, lengthen the pause at the top, or move to the Push-Up with an extra shoulder blade push at the top.

Stop if you feel sharp pain in the front or top of the shoulder, pinching under the collarbone, pain at the elbow, or numbness or tingling down the arm. A shoulder blade that visibly wings even at light loads is worth having a physical therapist assess before you keep loading it.

Frequently Asked Questions

Q: How is this different from a Smith machine incline bench press?

In the Smith Machine Incline Bench Press the elbows bend and the chest, shoulders and triceps push the bar. In the shoulder raise the elbows stay locked, and the bar moves only because the shoulder blades slide forward, which puts the work on the serratus anterior.

Q: Why is it done on an incline instead of a flat bench?

On an incline the arms sit above shoulder height relative to the torso, so the shoulder blade has to rotate upward as well as slide forward, and upward rotation is one of the serratus anterior's main jobs. A flat bench works too, but it trains the same protraction with the arms at a lower angle.

Q: How heavy should the bar be?

Lighter than you would expect. Pick a load you can lift for 10 to 15 reps with straight elbows, no shrug and a one-second pause at the top, and add weight only when every rep looks the same.

Q: Can I do it without a Smith machine?

Yes. The same movement works with a barbell or a pair of dumbbells on an incline bench, though a free barbell needs a spotter or safety arms because it hangs over your face. Bodyweight options such as Scapular Retraction and Protraction train the same shoulder blade motion with no bar at all.

Q: What incline should the bench be set to?

A moderate incline of around 30 to 45 degrees, with the bar directly above your shoulders when your arms are vertical, keeps the arms above shoulder height without turning the bench into a near-upright seat. Steeper settings push the bar toward an overhead position where shrugging becomes harder to avoid.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.