Viking Press

What Is the Viking Press?
Viking Press is a compound exercise that primarily targets the shoulders and also engages the triceps, upper back, core, and legs. It is an intermediate-level movement in which you press a pair of handles overhead on a plate-loaded lever arm that pivots from a fixed point, so the handles travel along a set arc instead of a free path. The handles face each other, which puts your hands in a neutral grip, palms in.
The Viking press is a long-standing strongman event. It is usually contested for as many reps as possible in a set time, often 60 seconds, or for a heavy max. Competition rules generally allow either a strict press or a single dip and drive from the legs, but a second knee bend to get under the handles is a no-rep, and a rep only counts at full elbow lockout. Strongman athletes also use it in training as heavy overhead work alongside implements like the log and axle, which are trained in the Log Clean and Press and Axle Clean and Press.
The deltoids and triceps do most of the work, while the upper traps and serratus anterior rotate the shoulder blades upward to finish the lockout. Because the pivot sits in front of you, the handles drift slightly forward as they rise, which brings in a little more upper chest than a vertical barbell press. The strict version keeps the work in the shoulders and triceps through the whole range. The push-press style uses a short dip and drive from the quads and glutes to move more weight and overload the top half, and standing up to lift the lever off its rest adds leg work in either style.
The Viking press suits strongman competitors and anyone who wants heavy overhead pressing without having to clean a bar to the shoulders or balance it overhead. Many coaches use it for lifters whose shoulders or wrists complain on a straight bar, since the neutral grip and fixed arc often feel more comfortable. Build a base first with the Barbell Overhead Press or Dumbbell Shoulder Press (Neutral Grip), and learn the dip and drive with the Push Press before loading the lever heavily.
Muscles Worked
- Deltoid
- Primary
- Gluteus Maximus
- Medium
- Serratus Anterior
- Medium
- Upper Trapezius
- Medium
- Vastus Lateralis
- Medium
Instructions
- Load the plates onto the lever and set it on its rest so the handles sit at about shoulder height when you are in a half squat.
- Face the pivot, step in between the handles, and set your feet about shoulder-width apart.
- Squat down under the handles and grip one in each hand with your palms facing each other, wrists stacked over your forearms and elbows slightly in front of the handles.
- Take a big breath, brace your core, and squeeze your glutes.
- Drive through your legs to stand up tall, lifting the lever off its rest while keeping the handles at your shoulders.
- Press the handles up and slightly forward along their arc, moving your head forward between your arms as they pass your face. For the push-press style, start the press with one short dip and drive of the legs, then keep your knees locked.
- Lock your elbows fully overhead with your biceps near your ears and your ribs down.
- Lower the handles under control back to your shoulders, rebrace, and repeat.
- After the last rep, squat down to set the lever back on its rest before letting go of the handles.
Common Mistakes
Leaning back
Arching the lower back to press more weight turns the lift into an incline press and loads the lumbar spine instead of the shoulders.
Fighting the arc
Trying to push the handles straight up instead of letting them travel up and slightly forward along the lever's path strains the shoulders and wastes force.
Flaring the elbows
Letting the elbows point straight out to the sides puts the shoulders in a weaker, more vulnerable position at the bottom of each rep.
Soft lockout
Stopping short of full elbow extension skips the hardest part of the range and does not count as a rep in strongman competition.
Re-bending the knees
Dipping a second time to get under the handles turns the press into a jerk, which takes work off the shoulders and is a no-rep in competition.
Poor setup position
Standing too close to or too far from the handles, or setting them too low, forces the shoulders and wrists into an awkward pressing angle from the first rep.
Injuries
Viking Press is a medium risk exercise when performed with proper technique. The loads are heavy and finish overhead, so the shoulders, the triceps tendon at the elbow, and the lower back take most of the strain. Leaning back to turn the press into an incline press strains the lower back, and letting the elbows flare straight out to the sides puts the shoulders in a weaker, more vulnerable position.
Warm up the shoulders and do a few lighter ramp-up sets before heavy work. Set the rest so the handles sit at shoulder height in a half squat rather than near the floor, keep your ribs down and glutes tight so your lower back stays neutral, and keep your elbows slightly in front of the handles instead of pointing out to the sides. If a rep stalls, lower the handles under control to your shoulders and squat the lever back onto its rest; never let go of the handles while the lever is overhead.
If the lever feels too heavy or your shoulders do not tolerate full overhead lockout yet, regress to the Landmine Press, the Dumbbell Shoulder Press (Neutral Grip), or the Machine Shoulder Press. Once strict reps are solid, progress with the dip-and-drive style, timed rep sets, or a free implement like the Log Clean and Press.
Stop the set if you feel a sharp or pinching pain at the front or top of the shoulder, pain in the elbow at lockout, pain in your lower back, or numbness or tingling down the arm, and get it assessed if it does not settle.
Frequently Asked Questions
- Q: Is the Viking press easier on the shoulders than a barbell overhead press?
For many lifters it is. The neutral grip and the fixed arc often feel more comfortable than a straight bar for people whose shoulders or wrists complain on the Barbell Overhead Press, but it still loads the shoulder overhead, so pain that persists needs an assessment rather than a different implement.
- Q: Should I use leg drive on the Viking press?
Both styles are worth training. Strict presses build shoulder and triceps strength through the whole range, while a single dip and drive lets you handle more weight and practice the lockout. In strongman competition one dip and drive is usually allowed, but bending the knees a second time is a no-rep.
- Q: How is the Viking press different from a landmine press?
A Landmine Press presses one end of a barbell at a forward angle, often with one arm, which adds an anti-rotation demand. The Viking press uses a two-handled lever pressed with both arms to full overhead lockout, so it takes more weight and stays closer to a true overhead press.
- Q: Can I do a Viking press without a dedicated Viking press machine?
Yes. Viking handle attachments that fit a landmine or a barbell sleeve, and two barbells anchored in a rack corner, recreate the movement closely. Each setup changes the arc and the start height slightly, so set the handles at shoulder height and practice the lockout with light weight first.
- Q: How many reps should I do on the Viking press?
Strongman events usually test reps in 60 seconds or a heavy max, so competitors train both heavy sets of 1 to 5 reps and longer timed sets. For general strength and muscle, 3 to 4 sets of 6 to 12 reps with a weight you can lock out cleanly works well.




