Cable Lying Face Pull

What Is the Cable Lying Face Pull?
Cable Lying Face Pull is a compound exercise that primarily targets the shoulders, with the rear deltoids and the external rotators of the rotator cuff doing most of the work, and it also engages the middle trapezius and rhomboids of the upper back. It is a beginner-level movement performed lying face up on a flat bench beneath a high pulley, pulling a rope from arm's length down to the sides of the face.
The face pull trains the muscles that pull the arms out and back and rotate the shoulders outward, a pattern that most pressing and rowing work barely touches. Trainers often program it alongside heavy bench and overhead pressing to give the back of the shoulder direct work, either as light sets in the warm-up or as higher-rep accessory work later in the session.
Lying on the bench is what sets this version apart from the Cable Standing Face Pull. The bench supports the head, spine and hips, so there is no need to brace the legs and lower back against the cable, and no way to lean back and borrow momentum from the torso. That makes it a strict, easy-to-learn version for beginners, and a useful option when the lower back is already tired from heavier lifts. The trade-off is setup: it needs a high pulley that hangs directly over the end of a bench. The Band Face Pull trains the same pattern with a band, while the Ring Face Pull and TRX Face Pull use body weight and add a trunk-stability demand the lying version removes.
Where the hands finish decides which muscles work hardest. Driving the elbows out wide keeps the load on the rear deltoids, finishing with the hands beside the ears and the forearms rotated back toward the machine brings in the external rotators, and squeezing the shoulder blades together against the bench adds the middle trapezius and rhomboids. Pulling toward the chest instead turns the rep into something closer to a pulldown and shifts the work toward the lats.
Anyone who presses regularly can benefit, from beginners to experienced lifters. If the shoulders cannot yet rotate back comfortably under load, build up with Band Shoulder External Rotation, Dumbbell Side-Lying Shoulder External Rotation and the Band Pull Apart first.
Muscles Worked
- Deltoid
- Primary
- Infraspinatus
- High
- Teres Minor
- High
- Upper Trapezius
- High
- Lower Trapezius
- Medium
- Rhomboid Major
- Medium
- Brachialis
- Low
Instructions
- Attach a rope to a high pulley and place a flat bench lengthwise with its head end under the pulley, so the cable hangs straight down over where your face will be. Wedge or weight the bench if it can slide.
- Sit on the bench, reach up and hold one end of the rope in each hand with your palms facing each other.
- Lie back with your head, upper back and hips on the bench and your feet flat on the floor, knees bent.
- Start with your arms straight and pointing up toward the pulley, the cable vertical and your shoulder blades set against the bench.
- Pull the rope down toward your face, driving your elbows out wide to the sides and separating the ends of the rope.
- Finish with your hands beside your ears, elbows bent and your upper arms roughly level with your shoulders, forearms rotated back toward the machine. Squeeze your shoulder blades together into the bench.
- Pause briefly, then straighten your arms back up along the same path under control, stopping just before the stack touches down.
- Keep your head and lower back on the bench throughout. After the last rep, return to straight arms and let the stack settle before you let go of the rope.
Common Mistakes
Pulling to the chest
Letting the elbows tuck toward the ribs and the rope finish over the chest turns the face pull into a pulldown and moves the work away from the rear shoulders.
Skipping the rotation
Stopping with the hands in front of the face instead of beside the ears leaves out the outward shoulder rotation that sets the face pull apart from a row.
Using too much weight
A load you cannot pause with at the face forces you to jerk the rope and cut the rotation short, which shifts the effort to the arms and strains the shoulder.
Letting the stack pull the arms up
Releasing the rope quickly on the way back lets the weight snap the arms straight and lift the shoulders off the bench instead of lowering under control.
Placing the bench in the wrong spot
If the cable does not hang straight down over your face, the rope travels in an arc toward the head or chest and the pull no longer follows a face pull path.
Lifting the head off the bench
Raising the head to meet the rope strains the neck and hides an incomplete pull, so keep the head down and bring the rope to it.
Injuries
Cable Lying Face Pull is a low risk exercise when performed with proper technique. The bench supports the head and spine and the load is usually light, so the stress lands almost entirely on the shoulders. The rotator cuff tendons at the back of the shoulder and the front of the shoulder joint are the usual strain points, mostly when the weight is too heavy to finish the rotation under control or when the elbows are forced far below the level of the bench at the end of each rep.
Set the bench so the cable hangs straight down over your face, and wedge it against the machine frame or weight it down if it can slide toward the stack. Pick a weight you can pause with at the face on every rep, finish with the upper arms roughly level with the shoulders rather than pushing them toward the floor, and rotate the forearms back only as far as is comfortable. Lower the rope with control instead of letting the stack pull the arms back up.
If the lightest plate is still too heavy, or the end position pinches, regress to the Band Face Pull, the Band Pull Apart or Dumbbell Side-Lying Shoulder External Rotation. Once the pattern is solid, the Cable Standing Face Pull allows more load and adds a bracing demand, and the Ring Face Pull and TRX Face Pull make the trunk hold the body in line as well.
Stop the set if you feel sharp or pinching pain at the front or top of the shoulder, painful clicking in the joint, or numbness or tingling running down the arm. Pain that lingers after training or returns every session is worth having a clinician assess.
Frequently Asked Questions
- Q: Why do face pulls lying down instead of standing?
The bench holds your head, spine and hips still, so you cannot lean back to cheat and you do not need to brace against the cable. That makes it a strict way to learn the pattern or to train the rear shoulders when your lower back is tired, while the Cable Standing Face Pull needs no bench placement and lets you handle more weight.
- Q: Where should the bench go relative to the pulley?
Place the head end of a flat bench under the high pulley so the cable hangs straight down over your face when you lie back. If the pulley sits behind your head or over your chest, the rope travels in an arc and the movement drifts toward a pullover or a pulldown.
- Q: What grip should I use on the rope?
Hold one end of the rope in each hand with your palms facing each other, as you would for a standing face pull. This neutral grip lets your hands separate and your forearms rotate back beside your ears at the end of each rep.
- Q: How heavy should I go and how many reps?
Keep the weight light enough to pause with the rope at your face on every rep, usually for sets of around 12 to 20 reps. If you have to jerk the rope or your shoulders leave the bench, the weight is too heavy.
- Q: Should I do lying face pulls before or after pressing?
Either works. Light sets make a good warm-up for the rear shoulders and upper back before bench or overhead pressing, and harder sets fit well as accessory work at the end of an upper-body session.




