Dumbbell Poliquin Lateral Raise

Dumbbell Poliquin Lateral Raise

What Is the Dumbbell Poliquin Lateral Raise?

Dumbbell Poliquin Lateral Raise is an isolation exercise that primarily targets the shoulders, especially the side deltoid, and also engages the upper trapezius and the rotator cuff. It is an intermediate-level movement that splits every rep into three parts: a lateral raise with the elbows bent to about 90 degrees, a pause at shoulder height where the arms straighten out to the sides, and a slow lowering with the arms straight. The exercise carries the name of the late strength coach Charles Poliquin.

The sequence is built around leverage. Bending the elbows keeps the dumbbells close to the shoulders, so the deltoids lift a short lever and can raise a weight they could not lift with straight arms. Straightening the arms at the top moves the dumbbells far from the shoulder joint, so the lowering phase is the hardest part of the rep, and it takes advantage of the fact that muscles can control more load while lowering than while lifting. The bent-arm lift is the easier half: in a study of competitive bodybuilders, a seated lateral raise with the elbows bent to 90 degrees produced less side-delt activity during the lift than a straight-arm raise with the thumbs forward, each done with its own 8-rep max.

It is a bodybuilding accessory for shoulder width rather than a strength or sport lift, and it usually sits near the end of a shoulder or upper-body session, after pressing work such as the Dumbbell Shoulder Press. The slow straight-arm lowering adds time under tension to side-delt training, which makes it a useful way to vary a program that already includes the standard Dumbbell Lateral Raise.

It suits lifters who can already perform a strict lateral raise without shrugging or swinging. The weight is limited by what you can lower slowly with straight arms, not by what you can lift with bent arms, so it is easy to pick a dumbbell that is too heavy. Anyone new to shoulder isolation work should first build control with the Dumbbell Lateral Raise or the Dumbbell Seated Lateral Raise before adding the bent-arm lift and slow lowering.

Muscles Worked

MuscleActivation
Deltoid
Primary

Instructions

  1. Stand tall with your feet about hip-width apart, holding a dumbbell in each hand with your arms hanging at your sides.
  2. Brace your core and set your shoulder blades down and slightly back.
  3. Bend your elbows to about 90 degrees so your forearms point forward and your palms face each other, keeping your upper arms against your sides.
  4. Keeping that elbow angle, raise your elbows out to the sides until your upper arms are level with your shoulders, so the dumbbells finish just in front of your shoulders with your palms facing the floor.
  5. Pause briefly, then straighten your elbows smoothly so your arms point straight out to the sides at shoulder height, palms still facing the floor.
  6. Lower your straight arms slowly to your sides, taking about 3 to 4 seconds, without letting your shoulders shrug.
  7. At the bottom, bend your elbows back to 90 degrees and repeat for the planned number of reps.
  8. Breathe out as you raise the dumbbells and breathe in as you lower them.

Common Mistakes

  • Choosing the weight for the lift

    Picking a dumbbell you can raise with bent arms but cannot lower slowly with straight arms turns the most important part of the rep into a drop.

  • Rushing the lowering

    Letting the straight arms fall to your sides in a second or less skips the slow lowering phase the exercise is built around, so take about 3 to 4 seconds.

  • Straightening the arms too early

    Opening the elbows before the upper arms reach shoulder height lengthens the lever partway up and usually ends in a swing to finish the rep.

  • Shrugging the shoulders

    Lifting the shoulders toward the ears shifts the work to the upper trapezius and crowds the front of the shoulder.

  • Raising above shoulder height

    Taking the elbows or straight arms higher than the shoulders adds little side-delt work and narrows the space under the acromion.

  • Swinging the torso

    Rocking the hips or leaning back to start the bent-arm lift hands the work to momentum instead of the deltoids.

Injuries

Dumbbell Poliquin Lateral Raise is a low risk exercise when performed with proper technique. The loads are light compared with pressing, but the straight-arm lowering holds the dumbbells on a long lever at shoulder height, so most problems come from choosing a weight sized for the bent-arm lift rather than for the lowering. The usual strain points are the front and top of the shoulder, where the rotator cuff tendons pass under the acromion, the upper trapezius and neck when the shoulders shrug, and the elbows if they snap straight under load.

To protect the shoulders, stop the raise when the upper arms reach shoulder height, keep the shoulder blades set down, and straighten the elbows smoothly rather than snapping them open. Keep the palms facing the floor at the top instead of tipping the thumbs down, since turning the arm inward at shoulder height narrows the space the rotator cuff tendons pass through. Choose a dumbbell you can lower for the full count with straight arms, and drop the weight as soon as the arms start to fall quickly.

If the full movement is too demanding, return to the Dumbbell Lateral Raise with a light weight, or use the Dumbbell Seated Lateral Raise to take the hips out of the lift. The Band Lateral Raise and Cable Lateral Raise are gentler options for building control. Progress by slowing the lowering phase first, then add weight in the smallest jumps available.

Stop the set if you feel a sharp or pinching pain at the front or top of the shoulder, pain or tingling running down the arm, or pain at the elbow as it straightens. Shoulder pain that persists between sessions should be checked by a physical therapist or physician before you return to overhead and lateral raising work.

Frequently Asked Questions

Q: Why bend the arms on the way up and straighten them at the top?

Bent elbows shorten the lever, so you can lift a weight to shoulder height that you could not raise with straight arms. Straightening the arms at the top lengthens the lever, so the deltoids then have to control that weight on the way down, where muscles can handle more load than on the way up.

Q: How heavy should the dumbbells be?

Choose a weight you can lower with straight arms for a slow count of 3 to 4 seconds on every rep. If the arms drop quickly or your shoulders shrug during the lowering, the dumbbells are too heavy, even if the bent-arm lift felt easy.

Q: Is the Poliquin lateral raise better than a regular lateral raise?

Not necessarily. It is a way to add a heavier, slower lowering phase to side-delt training, and it works best rotated with the Dumbbell Lateral Raise or the Cable Lateral Raise rather than replacing them.

Q: How many sets and reps should I do?

Two to four sets of 8 to 12 controlled reps suit most lifters, because the slow lowering already makes each rep long. Place it near the end of a shoulder or upper-body session, after your pressing work.

Q: Can I do Poliquin raises seated?

Yes, sitting upright on a bench takes the hips and knees out of the lift and makes it harder to swing the weight up. The arm path stays the same: bent-arm raise, straighten at shoulder height, then lower slowly with straight arms.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.