EZ Bar Bent-Over Row (Reverse Grip)

What Is the EZ Bar Bent-Over Row (Reverse Grip)?
EZ Bar Bent-Over Row (Reverse Grip) is a compound exercise that primarily targets the back and also engages the biceps, rear shoulders and lower back. It is an intermediate-level movement because holding a flat-backed hip hinge while rowing takes practice, so newer lifters should learn it with an empty or lightly loaded bar.
The lifter holds an EZ bar underhand on its angled grips, hinges forward to about 45 degrees and pulls the bar to the lower abdomen. Like the straight-bar Barbell Bent-Over Row (Reverse Grip), often called the Yates row, the underhand grip keeps the elbows close to the sides, so the pull comes mostly from the lats drawing the upper arms back, and the biceps are in a strong position to help. Grip choice does not reliably shift the work toward the lower lats; treat it as a change in pulling angle and arm involvement.
What the EZ bar changes is the forearm position. A straight bar held underhand turns the palms fully up, which some lifters feel in the wrists, forearms or the inside of the elbow. The EZ bar's angled grips turn the palms partly toward each other, a position between palms-up and neutral that many lifters find more comfortable while the rowing pattern stays the same. The trade-offs are a grip width set by the bends and a shorter bar with shorter sleeves that holds fewer plates, so this version suits moderate loads and higher rep ranges better than very heavy rowing.
It works well as a main or secondary back exercise, and it is a practical swap for lifters whose wrists or elbows complain on straight-bar underhand rows. If holding the hinge is the limiting factor, build up with the chest-supported Dumbbell Incline Row or the Barbell Inverted Row (Underhand Grip) first. Thinking about driving the elbows back rather than lifting the bar with the hands keeps the back doing the work instead of turning each rep into a curl.
Muscles Worked
- Latissimus Dorsi
- Primary
- Biceps Brachii
- High
- Brachialis
- High
- Brachioradialis
- Medium
- Deltoid
- Medium
- Erector Spinae
- Medium
- Rhomboid Major
- Medium
- Teres Major
- Medium
- Upper Trapezius
- Medium
Instructions
- Load the EZ bar and stand tall with your feet about hip-width apart.
- Grip the bar underhand on the angled sections closest to shoulder width, so your palms face up and slightly inward.
- Soften your knees and hinge at the hips until your torso is about 45 degrees to the floor, with your back flat and the bar hanging at arm's length near knee height.
- Brace your core, keep your head in line with your spine and keep your wrists straight.
- Pull the bar toward your lower abdomen by driving your elbows back, keeping them close to your sides.
- Squeeze your shoulder blades together at the top without lifting your torso.
- Lower the bar under control until your arms are straight, without letting it drop the last few inches.
- Repeat for the desired reps, then stand up by driving your hips forward and set the bar down.
Common Mistakes
Curling the bar
Bending the elbows to lift the bar before the shoulders move back turns the row into a curl and lets the biceps tire out long before the back does.
Standing up as the bar rises
Lifting the torso to finish each rep shortens the pull and shifts the work toward the upper traps.
Rounding the lower back
Letting the spine bend under load takes the work away from the hip and back muscles and strains the lower back.
Swinging with the hips
Using a hip thrust to heave the bar up adds momentum that strains the lower back and usually means the load is too heavy.
Bending the wrists back
Letting the bar roll toward the fingers cocks the wrists back and loads the forearms, undoing the comfort the angled grips are meant to give.
Dropping into a dead hang
Letting the bar fall the last few inches and jerking it back up loads the biceps tendon with the arm straight and palm up, its most vulnerable position.
Injuries
EZ Bar Bent-Over Row (Reverse Grip) is a medium risk exercise when performed with proper technique. The lower back works hard to hold the hinge, and a comparison of three rowing exercises in seven healthy men found the standing bent-over row placed the largest load on the lower spine, while the inverted row placed the lowest. Strain is most likely when the back rounds late in a set or the hips start swinging the bar up.
The underhand grip also loads the front of the elbow. A review of 56 filmed distal biceps tendon ruptures found nearly all happened with the forearm turned palm-up and the elbow straight or only slightly bent under a pulling load, most often during deadlifts. The EZ bar's angled grips take the wrists out of a fully palms-up position, which many lifters find more comfortable, but the bottom of every rep still puts the arm close to that position, so lower the bar smoothly and never jerk it up from a dead hang.
Use a load you can row with a flat back for every rep, warm up with lighter sets, and keep the wrists straight instead of letting the bar roll toward the fingers. If the lower back tires before the upper back, switch to the Dumbbell Incline Row or the Barbell Inverted Row (Underhand Grip). If the elbows still ache with the EZ bar, try the overhand Barbell Bent-Over Row or the Dumbbell Bent-Over Row, where the wrists can turn freely. Once the movement is solid, the straight-bar Barbell Bent-Over Row (Reverse Grip) allows heavier loading.
Stop the set if you feel sharp pain at the front of the elbow, a pop, sudden weakness, pain or numbness traveling down a leg, or if you can no longer keep your back from rounding. A pop at the elbow followed by bruising or weakness needs prompt medical evaluation.
Frequently Asked Questions
- Q: Why use an EZ bar instead of a straight bar for underhand rows?
The angled grips turn your palms partly toward each other, which many lifters find easier on the wrists and elbows than the fully palms-up position a straight bar forces. The pull and the muscles doing it stay essentially the same, so pick the bar that feels better and move to the straight-bar Barbell Bent-Over Row (Reverse Grip) when you want heavier loads or a different grip width.
- Q: Which bends of the EZ bar should I hold?
Use the pair of bends that puts your hands closest to shoulder width. That lets your forearms hang roughly straight down so your elbows can travel back close to your ribs.
- Q: How far should I bend over?
About 45 degrees is a practical middle ground. A more horizontal torso lengthens the pull but asks more of the lower back, while a more upright torso allows heavier loads with a shorter pull that can drift into a shrug.
- Q: Is the underhand grip safe for my elbows?
For most lifters it is, as long as the load is controlled and the bar is lowered smoothly rather than dropped into a dead hang. If the front of the elbow still hurts with the EZ bar, switch to the overhand Barbell Bent-Over Row and have persistent pain checked.
- Q: Can beginners do this exercise?
Yes, with a light bar and after learning to hold a flat-backed hip hinge. If the lower back gives out first, start with a chest-supported option like the Dumbbell Incline Row and come back to the bent-over version later.




