Smith Machine Bent-Over Row (Reverse Grip)

Smith Machine Bent-Over Row (Reverse Grip)

What Is the Smith Machine Bent-Over Row (Reverse Grip)?

Smith Machine Bent-Over Row (Reverse Grip) is a compound exercise that primarily targets the back and also engages the biceps, rear shoulders and lower back. It is an intermediate-level movement in which you hinge forward at the hips and pull a bar that runs on fixed rails toward your lower stomach, holding it with an underhand grip.

The guided bar takes care of balance, so you can concentrate on pulling and on holding your torso angle. That makes it a useful main or secondary horizontal pull in a back session, usually in moderate rep ranges such as 8 to 12, and a steady way to load a row when a free barbell keeps drifting forward or swinging. The underhand barbell row is often called the Yates row after bodybuilder Dorian Yates, though that version is usually done with a more upright torso than the bent-over position shown here.

Compared with the overhand Smith Machine Bent-Over Row, the underhand grip keeps your elbows close to your sides and sends them back toward your hips. That path leans on the lats and teres major and puts the biceps in a stronger pulling position, while the rear shoulders and upper traps do a little less than they do when the elbows flare wide. The grip is often said to target the lower lats, but the change you can count on is the elbow path, not a shift to one region of the muscle.

The row suits lifters who already have a solid hip hinge and want to train the back with less balance demand than the Barbell Bent-Over Row (Reverse Grip). If your lower back tires before your upper back, build up with a supported row such as the Machine Chest-Supported Row or the Cable Seated Row, and practice holding the bent-over position with the Smith Machine Romanian Deadlift.

Muscles Worked

MuscleActivation
Deltoid
Medium

Instructions

  1. Set the bar on the hooks at about knee height and the safety stops just below where the bar will sit at the bottom of the rep.
  2. Stand facing the bar with your feet about hip-width apart and the bar just in front of your shins.
  3. Grip the bar underhand, palms facing forward, with your hands about shoulder-width apart.
  4. Lift the bar slightly and rotate it off the hooks.
  5. Bend your knees slightly and push your hips back until your torso is about 45 degrees to the floor or a little lower, letting your arms hang straight with the bar in front of your shins.
  6. Keep your back flat and your neck in line with your spine, with your eyes on the floor a little ahead of you.
  7. Brace your core and pull the bar toward your lower stomach by driving your elbows back close to your sides.
  8. Squeeze your shoulder blades together at the top without shrugging or lifting your torso.
  9. Lower the bar under control until your arms are straight, keeping your torso angle the same.
  10. After the last rep, rotate the bar back onto the hooks before standing up.

Common Mistakes

  • Wrong distance from the bar

    The bar cannot move toward you on the rails, so standing too far back makes you reach and round your upper back, while standing too close makes the bar scrape your knees.

  • Curling the bar

    Bending the elbows first and flexing the wrists turns the row into a heavy curl, taking work off the back and loading the biceps tendon.

  • Rising up during the set

    Letting the torso creep upright as you tire shortens the pull and turns it into a shrug toward the chest.

  • Rounding the lower back

    Losing the flat back under load shifts the strain from the hips and back muscles onto the spine.

  • Dropping into the bottom

    Letting the bar fall until the elbows snap straight and then jerking it back up loads the biceps tendon at its most vulnerable point.

  • Pulling too high

    Aiming the bar at the chest flares the elbows and hikes the shoulders, losing the lat-focused path the underhand grip is meant to give.

Injuries

Smith Machine Bent-Over Row (Reverse Grip) is a medium risk exercise when performed with proper technique. The two main strain points are the lower back, which has to hold the hinge for the whole set, and the front of the elbow, where the underhand grip loads the biceps tendon. In a study of seven healthy men, the standing bent-over row placed a larger load on the lumbar spine than an inverted row or a one-arm standing cable row. The rails take away the balancing, not that load, so brace before every rep and keep the back flat.

Distal biceps tendon injuries usually happen when a bent, palms-up elbow is forced straight under heavy load. Lower the bar under control, avoid yanking it up from a dead hang at the bottom, and pull with the elbows rather than curling the bar. If your wrists or elbows feel strained in full supination, adjust your grip width slightly or switch to the angled grip of the EZ Bar Bent-Over Row (Reverse Grip) or the overhand Smith Machine Bent-Over Row.

Set the safety stops just below the bottom of the rep and stand so the bar hangs just in front of your shins. To take the lower back out of it, regress to the Machine Chest-Supported Row, the Chest-Supported T-Bar Row or the Cable Seated Row. Progress by adding load only once every rep keeps the same flat back and torso angle.

Stop the set if you feel sharp lower back pain, pain or tingling running down a leg, or a pop, sharp pain or sudden weakness at the front of the elbow. A pop with bruising or weakness needs prompt medical evaluation.

Frequently Asked Questions

Q: How is it different from the overhand Smith machine row?

The underhand grip keeps your elbows tucked and moving back toward your hips, so the bar finishes lower, near your stomach, and the biceps help more. The overhand Smith Machine Bent-Over Row lets the elbows travel wider and gives the rear shoulders and upper back a larger share.

Q: Is this the same as a Yates row?

Not quite. The Yates row is an underhand row usually done with a more upright torso, which allows heavier loads over a shorter range, while this version is bent further forward and runs on a guided bar. For the free-weight version, see the Barbell Bent-Over Row (Reverse Grip).

Q: Does the reverse grip train the lower lats more?

Not in a way you can count on. What the underhand grip clearly changes is the elbow path, keeping the elbows close and driving them back toward the hips, so think of it as a lat-heavy row rather than a lower-lat exercise.

Q: Is the Smith machine version easier than a barbell row?

It is easier to balance because the bar runs on rails, but your lower back still has to hold the hinge for the whole set. Loads are not directly comparable either, since Smith bars differ in weight and some are counterbalanced, so track your numbers on the same machine.

Q: What should I do if the underhand grip bothers my elbows or wrists?

Keep your wrists straight, lower the bar under control and try a slightly narrower or wider grip. If it still hurts, use the angled grip of the EZ Bar Bent-Over Row (Reverse Grip) or switch to an overhand grip, and stop for any sharp pain at the front of the elbow.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.