Smith Machine Incline Row

Smith Machine Incline Row

What Is the Smith Machine Incline Row?

Smith Machine Incline Row is a compound exercise that primarily targets the back and also engages the rear shoulders, biceps and forearms. It is a beginner-level movement in which you stand bent over the high end of an incline bench placed inside a Smith machine, rest your chest on the top of the pad and row the bar up toward the underside of the pad.

The pad is what sets this row apart. In a Smith Machine Bent-Over Row the lower back has to hold the hinge for the whole set, and that often gives out before the upper back does. Here the bench carries much of the torso's weight, so the set ends when the target muscles tire. The rails fix the bar path and the pad stops you from heaving with the hips, which makes it hard to cheat a rep and easy to compare loads from one session to the next.

With the overhand grip and the elbows traveling out to the sides, the work is spread across the mid and upper back: the trapezius, rhomboids and rear deltoids squeeze the shoulder blades together while the lats and teres major pull the arms back. Bringing the hands closer and keeping the elbows nearer the ribs shifts more of the pull to the lats, and an underhand grip adds biceps work. Because nothing else helps the bar up, most lifters use less weight than on a free-standing row.

It suits beginners learning to row with the shoulder blades rather than the arms, lifters whose lower back is already tired from squats or deadlifts, and anyone building back size who wants a strict accessory row late in a session. Focusing on squeezing the shoulder blades together at the top and letting them spread at the bottom matters more here than the load on the bar. If standing bent over the pad is uncomfortable, a seated option such as the Machine Seated Row or the Cable Seated Row trains the same pull.

Muscles Worked

MuscleActivation

Instructions

  1. Set an adjustable bench to an incline and place it inside the Smith machine with the high end facing you, so the bar travels just below the top edge of the pad.
  2. Set the bar on the hooks low enough to reach with straight arms from the pad, and set the safety stops just below that height.
  3. Stand at the high end of the bench with your feet about hip width apart and your knees slightly bent.
  4. Hinge forward and rest your chest on the top of the pad, with your torso close to parallel to the floor and your head in line with your spine.
  5. Grip the bar overhand, slightly wider than shoulder width, and rotate it off the hooks with your arms straight.
  6. Draw your shoulders down and back, then row the bar up toward the underside of the pad by driving your elbows up and out to the sides.
  7. Pause briefly at the top with your shoulder blades squeezed together and your chest still on the pad.
  8. Lower the bar under control until your arms are straight and your shoulder blades spread apart.
  9. Repeat for the desired number of reps, then rotate the bar back onto the hooks before standing up.

Common Mistakes

  • Lifting the chest off the pad

    Raising the chest to heave the bar up turns the movement into an unsupported bent-over row and puts the load back on the lower back, which usually means the weight is too heavy.

  • Shrugging toward the ears

    Pulling the shoulders up lets the upper traps take over, so keep them drawn down and drive the elbows back instead.

  • Cutting the bottom short

    Stopping before the arms straighten and the shoulder blades spread apart skips the stretched part of the rep where the upper back does much of its work.

  • Yanking or bouncing the bar

    Jerking the bar up or dropping it onto the safety stops replaces back work with momentum and jars the elbows and shoulders.

  • Bench in the wrong spot

    Because the bar runs on fixed rails, a bench set too far forward or back makes the bar hit the pad early or pull toward the stomach instead of the lower chest.

  • Craning the neck

    Lifting the head to look forward strains the neck, so let it hang in line with the spine beyond the end of the pad.

Injuries

Smith Machine Incline Row is a low risk exercise when performed with proper technique. The bench carries much of the torso's weight and the rails fix the bar path, so the lower back works far less than in a free-standing bent-over row and the bar cannot drift. The main strain points are the shoulders, the elbows and the chest where it presses into the top edge of the pad.

Keep the shoulders drawn down away from the ears and stop each rep once the elbows are just past the torso, rather than letting the front of the shoulder roll forward to squeeze out more range. Lower the bar under control instead of letting it drop to a hard stop at the bottom, which jolts the elbows and shoulders. Set the safety stops just below the lowest point of the rep, unhook and rehook the bar with the arms straight and the chest on the pad, and put a folded towel over the edge of the pad if it digs into your sternum.

If bending over the pad bothers your hips or lower back, a seated row such as the Machine Seated Row supports the body more fully. Once the movement is solid, the Barbell Incline Row asks you to balance the bar yourself, and the Chest-Supported T-Bar Row allows heavier loading. Stop the set if you feel sharp pain at the front or top of the shoulder, pain in the elbow, numbness or tingling in the hands, or pain in the lower back.

Frequently Asked Questions

Q: How should I set up the bench?

Place an incline bench inside the Smith machine with its high end facing you, and set the angle so the top of the pad sits around hip height when you lean over it. Your torso should rest close to parallel with the floor, and the bar should hang straight below your shoulders, just below the top edge of the pad.

Q: Is the Smith machine version better than using a free barbell?

Neither is better, as they suit different goals. The Smith machine fixes the bar path and has safety stops, so all the effort goes into pulling and loads are easy to track, while the Barbell Incline Row also makes you balance and steer the bar.

Q: Can I do this row if my lower back is tired or sore?

Often, yes. The pad supports much of your torso, so it is a common swap for bent-over rows when the lower back needs a break, but you still stand in a hip hinge, so stop if it causes back pain and use a seated row instead.

Q: Should I use an overhand or underhand grip?

Both work. An overhand grip slightly wider than shoulder width, with the elbows traveling out to the sides, spreads the work across the upper back and rear shoulders, while an underhand or closer grip keeps the elbows nearer the ribs and brings in more lats and biceps.

Q: Why can I lift less than on a bent-over row?

With your chest on the pad you cannot use your hips or legs to start the bar moving, and the rails stop you from adjusting the bar path mid-rep. Most lifters need a lighter weight, which is expected and means the back is doing the work.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.