Smith Machine Single-Arm Bent-Over Row

Smith Machine Single-Arm Bent-Over Row

What Is the Smith Machine Single-Arm Bent-Over Row?

Smith Machine Single-Arm Bent-Over Row is a compound exercise that primarily targets the back and also engages the rear shoulders, biceps, forearms and core. It is a beginner-level movement in which you hinge forward facing a Smith machine bar, hold it with one hand in an overhand grip directly below your shoulder, and row it from arm's length up toward your hip.

The exercise trains the lats and the muscles between the shoulder blades one side at a time. Because the bar runs on a fixed track, you never have to balance it, the hooks let you rack it at any point, and loading it heavier than the dumbbell rack allows takes nothing more than a plate. That makes it a practical back accessory after pull-ups or a heavier two-handed row, a good fit for higher-rep sets, and a simple way to give a weaker side the same work as the stronger one.

The Smith bar can only travel straight up and down, so with your torso leaning forward your elbow sweeps back along your side as the bar rises toward your hip, which keeps the lats doing much of the work. Rowing toward the lower ribs with the elbow drifting wider shifts more of the effort to the upper back and rear shoulder. Working one side at a time also asks your trunk to resist twisting: a study of trained men comparing free-weight, cable and machine rows found the external obliques worked far harder when each row was done with one arm than with two, while the lower-back muscles generally worked less. Compared with the two-handed Smith Machine Bent-Over Row, you move less total weight but can focus on each side, and unlike the Landmine Single-Arm Bent-Over Row, the bar travels in a straight line rather than an arc.

This variation suits beginners learning to row from a hinge, lifters who want a steady unilateral row they can load progressively, and trainers looking for a controllable back exercise for clients who are not ready for a free barbell. If holding the hinge is the limiting factor, learn it first with the Dumbbell Romanian Deadlift and build rowing strength with a chest-supported option such as the Smith Machine Incline Row. Thinking about pulling your elbow toward your back pocket, rather than lifting the bar with your hand, helps you feel the lat do the work.

Muscles Worked

MuscleActivation

Instructions

  1. Set the bar hooks at about mid-thigh height and the safety stops a few inches lower, then load a light weight.
  2. Stand facing the bar with your feet about hip-width apart, close enough that the bar sits just in front of your thighs.
  3. Push your hips back and bend your knees until your torso is about 45 degrees to the floor, with your back flat and your neck in line with your spine.
  4. Grab the bar with one hand in an overhand grip, directly below that shoulder, and rest your free hand on your thigh just above the knee.
  5. Rotate the bar to unhook it and let your working arm hang straight, with your hips and shoulders square to the bar.
  6. Brace your core and drive your elbow up and back, pulling the bar along your thigh toward your hip.
  7. Squeeze your shoulder blade toward your spine at the top without twisting your torso or shrugging your shoulder.
  8. Lower the bar under control until your arm is straight again.
  9. Complete your reps, rotate the bar back onto the hooks, then switch hands and repeat on the other side.

Common Mistakes

  • Twisting the torso

    Rotating your chest open toward the working side uses trunk rotation to lift the bar and takes the work away from your back.

  • Rounding the lower back

    Letting your spine curve as the arm reaches down moves the load from your hips and back muscles onto your lower back.

  • Standing up as you row

    Raising your chest with each rep turns the row into a partial hip extension and shortens the pull your back has to make.

  • Shrugging the shoulder

    Hiking your shoulder toward your ear turns the row into a shrug and can pinch the front of the shoulder.

  • Standing at the wrong distance

    Because the bar can only move straight up and down, standing too far back pulls your shoulder forward and rounds your back, while standing too close jams the bar into your thighs.

  • Cutting the range short

    Stopping before your arm is straight or before the bar reaches your hip skips both the stretch and the full contraction of the lat.

Injuries

Smith Machine Single-Arm Bent-Over Row is a low risk exercise when performed with proper technique. Only one arm is loaded, the bar runs on a guided track and the safety stops can catch it, so the lower back carries less than in a two-handed bent-over row. The main strain points are still the lower back, which holds the hinge and has to stop your torso from twisting toward the bar, and the front of the working shoulder, which can be irritated by shrugging the bar up or by yanking it from a dead hang.

Set the safety stops a few inches below the bottom of your range before you start, and stand close enough that the bar travels just in front of your thighs. Brace your core, keep your hips and shoulders square to the bar, and rest your free hand on your thigh for support. Start light enough that you can row without twisting, and lower the bar under control instead of letting it drop to the end of your arm.

If your lower back tires or aches before your upper back does, switch to a supported row such as the Smith Machine Incline Row, Landmine Bench-Supported Single-Arm Row or Kettlebell Bench-Supported Single-Arm Row. To progress, add load gradually, pause with the bar at your hip, slow the lowering phase, or move to a free-weight version such as the Dumbbell Single-Arm Bent-Over Row.

Stop the set if you feel sharp or radiating pain in your lower back or down a leg, pinching at the front of the shoulder, or numbness or tingling in the working hand, or if you can no longer keep your back flat. Pain that lingers after training should be checked by a qualified professional before you load the movement again.

Frequently Asked Questions

Q: Should I face the bar or stand sideways to it?

Both setups are used. Facing the bar, as shown here, keeps your stance square and lets you switch sides by simply changing hands, while standing side-on puts the bar beside your hip and suits lifters who prefer a staggered stance.

Q: Where should I grip the bar?

Grip the bar directly below your working shoulder so your arm hangs straight down. The bar is fixed to the machine's guide rails, so it will not tip the way a free barbell would if you held it off center.

Q: What should I do with my free hand?

Rest it on your thigh just above the knee. It supports part of your upper body so your lower back has less to hold, and pressing lightly into your thigh also helps you keep your shoulders square.

Q: How is it different from the Smith Machine Bent-Over Row?

The Smith Machine Bent-Over Row uses both hands, so you can lift more total weight and your torso has no twist to resist. The single-arm version trains each side on its own, which helps when one side is stronger, and lets your free hand support your torso.

Q: Is it better than a dumbbell single-arm row?

Neither is better for building the back. The Smith machine keeps the bar on a fixed path and is easy to load past the heaviest dumbbell, while the Dumbbell Single-Arm Bent-Over Row lets your arm find its own path and makes you control the weight in every direction.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.