Barbell Block Power Clean

What Is the Barbell Block Power Clean?
Barbell Block Power Clean is a compound exercise that primarily targets the back, glutes, quads and hamstrings, and also engages the calves, shoulders and core. It is an advanced-level movement in which the bar starts motionless on blocks at about knee height, is pulled explosively and is caught on the front of the shoulders in a partial squat with the thighs above parallel.
The catch is what separates it from the Barbell Block Clean, which starts from the same blocks but receives the bar in a full front squat. Because the bar has to be pulled higher to be received above parallel, the block power clean rewards a complete, aggressive finish and a fast turnover, and it is usually done with less weight than a block clean. Compared with the Barbell Power Clean from the floor, the blocks remove the first pull, and compared with the Barbell Hang Power Clean, the dead stop removes the stretch a lifter gets from lowering into the hang, so the bar has to be accelerated from a standstill over a short distance.
Weightlifting coaches use it to train speed and rate of force development through the top of the pull, and as a lighter secondary lift on easier days, since the shorter pull and shallow catch tax the back and legs less than full cleans. Strength and conditioning coaches program power cleans and their derivatives for athletes in jumping and sprinting sports because the second pull shares the rapid hip, knee and ankle extension of those tasks. It belongs early in a session, while the lifter is fresh, in low-rep sets of 1 to 3.
It suits lifters who already power clean from the floor or the hang with solid positions. Anyone still learning the clean should first build the pattern with the Barbell Block Pull, the Barbell High Pull and front rack work in the Barbell Front Squat, then the hang power clean, before adding blocks. Block height changes the emphasis: higher blocks shorten the pull further and stress aggression, while lower blocks make the lifter keep the back angle as the bar passes the knees.
Muscles Worked
- Biceps Femoris
- Primary
- Erector Spinae
- Primary
- Gluteus Maximus
- Primary
- Vastus Lateralis
- Primary
- Adductor Magnus
- High
- Upper Trapezius
- High
- Vastus Medialis
- High
- Deltoid
- Medium
- Rectus Abdominis
- Medium
Instructions
- Set two solid, equal-height blocks so the loaded bar rests on them at about knee height.
- Stand with your feet about hip-width apart and the bar over your mid-foot.
- Take an overhand grip slightly wider than shoulder width, just outside your thighs, with straight arms.
- Push your hips back so they sit above your knees, with your shoulders slightly in front of the bar, back flat and chest up.
- Brace your trunk, take the slack out of the bar, then push through the floor to break it off the blocks with your arms long.
- As the bar passes your mid-thigh, drive your hips and knees to full extension and shrug, keeping the bar close to your body.
- Pull your elbows high and out to move yourself down under the bar, letting your feet shift slightly wider.
- Whip your elbows forward and receive the bar on the front of your shoulders.
- Stop the catch in a partial squat with your thighs above parallel, torso upright and weight over the whole foot.
- Stand up fully with your elbows high.
- Lower the bar to your hips, then back onto the blocks under control, and reset before the next rep.
Common Mistakes
Riding the catch into a full squat
Sinking below parallel to save the bar turns the lift into a block clean and means the load is too heavy or the pull too short for a power receive.
Jerking the bar off the blocks
Yanking the bar without first taking out the slack throws the hips and shoulders out of position and lets the back round.
Bending the arms early
Pulling with the arms before the hips and knees finish extending bleeds power from the legs and slows the bar.
Cutting the pull short
Dropping under the bar before reaching full extension leaves the bar too low to receive above parallel.
Swinging the bar and jumping forward
Bumping the bar away with the thighs makes it loop forward, so you have to jump after it to make the catch.
Catching with the elbows down
Receiving the bar on the hands with the elbows pointing down loads the wrists and lets the bar roll off the shoulders.
Injuries
Barbell Block Power Clean is a medium risk exercise when performed with proper technique. The fast turnover and catch load the wrists, elbows and shoulders in the front rack, the knees absorb the bar in the partial squat, and the lower back has to stay braced as the bar breaks off the blocks.
Most problems come from a load too heavy to receive above parallel, which leads to a crashing catch, a soft rack with the elbows down, or a back that rounds off the blocks. Work up in small jumps, keep the bar close, and use stable, equal-height lifting blocks rather than hollow plyo boxes or uneven stacks. Lift with bumper plates on a platform, and on a missed rep push the bar forward and step back so it falls clear of your body and the blocks.
If wrist or front rack mobility limits the catch, train the pull without it in the Barbell Clean Pull or Barbell Block Pull, and use the Barbell Hang Power Clean as a technique regression. Progress to the Barbell Block Clean or the full Barbell Power Clean from the floor.
Stop the set for sharp pain in the wrists, elbows, knees or lower back, if the bar keeps landing on your collarbones, or when fatigue makes the pull slow and the catch sloppy, because speed is the point of the lift.
Frequently Asked Questions
- Q: What is the difference between a block power clean and a block clean?
Both start from the same blocks, but a block power clean is received in a partial squat with the thighs above parallel, while a Barbell Block Clean is received in a full front squat. The deeper catch allows heavier loads and demands more from the legs on landing: in a study of 10 collegiate athletes cleaning 90% of their power clean max from the knee, the power catch absorbed less than half the work of the full squat catch.
- Q: How high should the blocks be?
Knee height is the usual starting point. Higher blocks, closer to mid-thigh, shorten the pull and stress speed and aggression, while lower blocks just below the knee make you hold your back angle as the bar passes the knees.
- Q: Is a block power clean the same as a hang power clean from the knee?
No. In a Barbell Hang Power Clean you lift the bar from the floor and lower it into the hang, which pre-stretches the hips before the pull, while the block version starts from a dead stop with no countermovement. That makes the bar harder to accelerate and the lift a stricter drill for producing force quickly from a set position.
- Q: Should I be able to lift more from blocks than from the floor?
Usually not, because the shorter pull gives you less distance to build bar speed for a power catch. If you consistently lift more from blocks than from the floor, it can point to a weakness in the first pull, which the Barbell Clean Deadlift and floor power cleans help address.
- Q: How many reps should I do per set?
Keep sets to 1 to 3 reps so every rep stays fast, and reset fully on the blocks between reps. Place the lift early in the session, or use it as a lighter secondary lift on easier training days.




