Smith Machine Incline Triceps Extension

Smith Machine Incline Triceps Extension

What Is the Smith Machine Incline Triceps Extension?

Smith Machine Incline Triceps Extension is an isolation exercise that primarily targets the triceps and also engages the shoulders and forearms to hold the arms and the bar in place. It is an intermediate-level movement in which you lie on an incline bench under a Smith machine bar, lower the bar toward your forehead by bending only the elbows, and press it back up by straightening them.

The incline changes where the upper arms sit. Lying back on an angled bench, your arms point up and slightly back past your head rather than straight up over your chest as in a flat Barbell Lying Triceps Extension. That position puts the shoulder further into flexion, which keeps the long head of the triceps, the only head that also crosses the shoulder, more stretched through the set. Coaches use the incline version when they want a little more long-head emphasis than a flat skull crusher gives, and many lifters find it easier on the elbows.

The Smith machine takes away the job of balancing the bar. The rail fixes the bar to a vertical line, so the bar cannot wander forward or back, and the safety stops can be set to catch it above your head. That makes it a useful option for training close to failure without a spotter. The trade-off is that the rail decides the bar path, so where you place the bench matters: set it so the bar comes down just above your forehead and your upper arms can stay nearly still from the bottom to the top.

This exercise usually comes near the end of a push or arm session, after compound pressing such as the Smith Machine Incline Bench Press (Close Grip) or the Smith Machine JM Press, and it is normally trained with moderate loads for 8 to 15 reps. It suits lifters who already have a pain-free lockout and can control a bar near their face. If you are new to triceps isolation, start with a Cable Triceps Pushdown With Rope or the Dumbbell Incline Triceps Extension and learn to keep the upper arms still before moving to the bar.

Muscles Worked

MuscleActivation

Instructions

  1. Set an incline bench to about 30 to 45 degrees and place it under the Smith machine so the bar will come down just above your forehead when you lie back.
  2. Set the safety stops a little above the lowest point of your forehead, then lie back with your head, upper back and hips on the bench and your feet flat on the floor.
  3. Grip the bar with an overhand grip about shoulder-width apart or slightly narrower.
  4. Press the bar up until your arms are straight, then rotate it to unhook it from the rack.
  5. Let your upper arms angle slightly back past your head and keep them there, with the elbows pointing up.
  6. Bend only your elbows and lower the bar under control for about two to three seconds until it is just above your forehead or hairline.
  7. Keeping the upper arms nearly still, straighten your elbows to press the bar back up to the start.
  8. Finish each rep with a smooth extension, without snapping the elbows into lockout.
  9. After the last rep, straighten your arms and rotate the bar to hook it back on the rack.

Common Mistakes

  • Flaring the elbows

    Letting the elbows drift out wide shifts stress onto the elbow joint and takes tension off the triceps, so keep them pointing up and roughly shoulder-width apart.

  • Turning it into a press

    Pulling the elbows down toward the chest as the bar rises turns the rep into a close-grip press, so keep the upper arms nearly still and move only at the elbows.

  • Dropping the bar

    Letting the bar fall into the bottom position loads the elbow tendon hardest exactly where it is most stretched, so lower it under control for about two to three seconds.

  • Bench in the wrong spot

    With the bench too far forward or back, the fixed rail drags the bar onto your face or far behind your head, so position the bench so the bar lands just above your forehead.

  • Skipping the safety stops

    Training without the stops set means a failed rep comes down on your head, so set them just above the lowest point of your forehead before you start.

  • Snapping into lockout

    Slamming the elbows straight at the top jars the joint, so finish each rep with a smooth, controlled extension.

Injuries

Smith Machine Incline Triceps Extension is a medium risk exercise when performed with proper technique. The bar travels over your face, and the elbows take the full load of every rep, so mistakes tend to show up as a bar dropping too low or as pain at the back of the elbow.

The most common strain point is the triceps tendon where it attaches above the elbow, especially when the weight is heavy, the reps are dropped fast into the bottom, or the elbows flare wide. The shoulders can also complain if the bar is lowered far behind the head on a bench placed too far back. Set the safety stops a little above the lowest point of your forehead before the first rep, so a missed rep lands on the stops and not on your head. Use a weight you can lower slowly for at least 8 reps, keep the elbows pointing up rather than out, and stop each rep at the depth your elbows tolerate.

If the movement bothers your elbows, regress to a Cable Triceps Pushdown With Rope or a Band Triceps Pushdown, which load the triceps with less stress at the bottom of the range. Once the Smith version feels solid, progress to the free-weight EZ Bar Incline Triceps Extension, which adds the balance the rail removes.

Stop the set if you feel sharp pain at the elbow, pain at the back of the elbow that lingers after training, or pain at the front of the shoulder. Posterior elbow pain that keeps returning when you straighten the arm against resistance should be assessed by a clinician before you load it again.

Other Names for the Smith Machine Incline Triceps Extension

The Smith Machine Incline Triceps Extension is also known as:

  • Smith Machine Incline Skull Crusher

Frequently Asked Questions

Q: Is the incline version better than a flat skull crusher?

It is not better, just different. The incline puts your upper arms further overhead, which keeps the long head of the triceps more stretched, and many lifters find it kinder to the elbows, while the flat Barbell Lying Triceps Extension usually allows a little more load.

Q: Why use a Smith machine instead of an EZ bar?

The rail removes the need to balance the bar and lets the safety stops catch a missed rep above your head, so you can push sets harder without a spotter. The EZ Bar Incline Triceps Extension lets the bar follow your own arc and puts the wrists at a more comfortable angle, so try both and keep the one your elbows prefer.

Q: What bench angle should I use?

A moderate incline of about 30 to 45 degrees works for most people. A steeper bench pushes the arms further overhead and the load toward the shoulders, so stay at the lower end if your shoulders feel tight.

Q: How far should I lower the bar?

Lower it until it is just above your forehead or hairline, with the upper arms still pointing up and back. Going deeper behind the head adds stretch but also stress on the elbows and shoulders, so only go as far as stays pain-free.

Q: How heavy should I go?

Pick a weight you can lower slowly for 8 to 15 clean reps without the elbows flaring or the upper arms swinging. Heavy, low-rep sets of skull crushers are a common cause of elbow pain, and compound presses are the better place for heavy triceps work.

Turn any exercise into a full workout.

Free for up to 5 clients, with 30 days of Pro to start. No credit card required.