Weighted Inverted Row

What Is the Weighted Inverted Row?
Weighted Inverted Row is a compound exercise that primarily targets the back and also engages the biceps, the rear shoulders and the muscles that hold the body rigid. It is an intermediate-level movement in which you hang under a barbell set in a power rack, with your heels resting on a flat bench and a weight plate lying on your torso, and row your chest up to the bar. Raising the feet to bench height brings the body close to horizontal, so you lift a larger share of your body weight than with your feet on the floor, and the plate adds load on top of that.
The inverted row is a horizontal pull, and the weighted version is mainly used as the next step once the bodyweight version with the feet elevated stops being challenging. Swapping plates lets you raise the load in small steps, so you can keep building strength in the pattern instead of only adding reps. It usually sits in the pulling part of an upper-body session, either as the main row or as an accessory after a vertical pull such as the Weighted Pull-Up.
The lats, rhomboids, middle and lower trapezius and rear deltoids share the work of pulling the chest to the bar and drawing the shoulder blades together, while the biceps, brachialis and brachioradialis bend the elbows. The glutes, hamstrings and abdominals keep a straight line from heels to shoulders, so the row also trains the trunk to stay stiff under load. A study comparing three rows in healthy young men found the inverted row produced the highest lat, upper-back and hip extensor activation and the lowest lower-back load of the three, while the standing bent-over row loaded the lower back the most. The overhand grip shown here keeps the emphasis on the upper back, while an underhand grip, as in the Barbell Inverted Row (Underhand Grip), brings in more of the biceps.
This variation suits lifters who can already complete 12 or more strict reps with their feet on a bench and their chest touching the bar on every rep. If that is not there yet, build up with the Bent-Knee Inverted Row, then the Barbell Inverted Row with the feet on the floor, then a feet-elevated version such as the TRX Feet-Elevated Inverted Row before adding a plate.
Muscles Worked
- Latissimus Dorsi
- Primary
- Rhomboid Major
- Primary
- Biceps Brachii
- High
- Deltoid
- High
- Lower Trapezius
- High
- Teres Major
- High
- Upper Trapezius
- High
- Brachialis
- Medium
- Brachioradialis
- Medium
- Gluteus Maximus
- Medium
Instructions
- Set a barbell securely in a power rack at about waist height, and place a flat bench in front of the rack so your heels can rest on it when you lie under the bar.
- Lie on the floor under the bar with the bar above your chest, and set one weight plate flat and centered on your lower chest and upper abdomen.
- Grip the bar overhand, slightly wider than shoulder width.
- Rest your heels on the bench, straighten your legs and lift your hips so your body forms a straight line from heels to shoulders, hanging from straight arms.
- Draw your shoulder blades back and pull your chest up to the bar, keeping your body rigid and the plate level.
- Pause briefly with your chest at the bar, squeezing your shoulder blades together without shrugging or pushing your chin forward.
- Lower yourself under control until your arms are fully straight, keeping your hips up.
- Repeat for the desired reps, then lower your hips slowly to the floor and lift the plate off your torso before sitting up.
Common Mistakes
Sagging hips
Letting the hips drop toward the floor bends the body at the waist, shortens the pull and shifts stress onto the lower back, so keep a straight line from heels to shoulders.
Stacking plates
Piling more than one plate on the torso, or using one too large to sit flat, lets the load slide toward the face as you row, so use a single plate or switch to a weighted vest.
Stopping short of the bar
Ending each rep several inches below the bar or not straightening the arms at the bottom cuts the range of motion, so add weight only when the chest still reaches the bar on every rep.
Shrugging and reaching with the chin
Lifting the shoulders toward the ears and pushing the head forward to meet the bar shifts the work to the upper traps and neck, so keep the neck long and pull with the shoulder blades.
Driving the elbows far behind the body
Pulling the elbows well past the torso at the top rolls the shoulders forward instead of drawing the shoulder blades together, so stop when the chest meets the bar.
Injuries
Weighted Inverted Row is a low risk exercise when performed with proper technique. The body hangs from the bar rather than bending over a load, so the lower back is spared compared with a Barbell Bent-Over Row. The strain points are the front of the shoulders when they roll forward at the top of the rep, the elbows and biceps tendons under high volume, and the lower back if the hips sag. The plate brings its own hazard: it rests on the torso without being held, and it can slide toward the face or off to the side if the body twists or the plate is too large.
Use one plate only, small enough to sit flat and centered on the lower chest and upper abdomen, and never stack several. Set the bar securely in the rack hooks before lying down, keep the body rigid so the plate stays level, and lower the hips to the floor slowly at the end of the set before lifting the plate off. A weighted vest, or a backpack loaded with plates and worn on the chest, holds the load more securely than a balanced plate and is the better choice for heavier sets. Finish each rep by squeezing the shoulder blades together, not by shrugging or driving the elbows far behind the body.
To regress, remove the plate, lower the feet to the floor as in the Barbell Inverted Row, or bend the knees as in the Bent-Knee Inverted Row. To progress, add load in small plate jumps or pause for a count of two at the top of each rep. Stop the set if you feel sharp pain at the front of the shoulder or inside the elbow, numbness or tingling in the hands, or if the plate starts to shift and you cannot hold it level.
- Primary Focus
- Back
- Equipment
- Barbell, weight plate, bench, and body weight
- Modality
- Strength
- Difficulty
- Intermediate
Alternative Exercises
Other Names for the Weighted Inverted Row
The Weighted Inverted Row is also known as:
- Weighted Australian Pull-Up
- Weighted Body Row
Frequently Asked Questions
- Q: Why are the feet on a bench instead of the floor?
Resting the heels on a bench brings the body close to horizontal, so you lift more of your own weight than with the feet on the floor, and it gives the plate a flatter surface to rest on. With the feet on the floor the body is more upright and the same plate makes a noticeably easier set.
- Q: Is a weighted vest better than a plate?
For heavier loads, usually yes. A vest, or a backpack loaded with plates and worn on the chest, stays in place as you move, while a balanced plate can slide, but a single plate works well for moderate loads and is quick to change between sets.
- Q: When should I start adding weight?
Add a plate once you can complete 12 or more strict reps with your feet on the bench, your body straight and your chest touching the bar on every rep. Start with a light plate and keep the same full range of motion.
- Q: How does it compare with a barbell bent-over row?
Both are horizontal pulls for the upper back, but in the inverted row you hang under the bar instead of holding a hinged position, so the lower back carries less load. The Barbell Bent-Over Row is easier to load heavily and also trains the hips and lower back to hold the hinge.
- Q: How wide should my grip be?
Take an overhand grip slightly wider than shoulder width, as shown. A much wider grip shortens the range of motion and shifts more work to the rear shoulders, while a narrower grip lets the elbows stay closer to the body.




